| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: sockmap: fix tail fragment offset in bpf_msg_push_data
When bpf_msg_push_data() inserts data in the middle of a scatterlist
entry, it splits the original entry into a left fragment and a right
fragment.
The right fragment offset is page-local, but the code advances it with
`start`, which is the message-global insertion point. For inserts into a
non-first SG entry, this over-advances the offset and leaves the split
layout inconsistent.
Advance the right fragment offset by the fragment-local delta,
`start - offset`, which matches the length removed from the front of the
original entry. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Add bounds checks for firmware log indices
Add validation that read and write indices in the firmware log buffer
are within valid bounds (< data_size) before using them. If
out-of-bounds indices are encountered (from firmware), clamp them to
safe values instead of proceeding with invalid offsets.
This prevents potential out-of-bounds buffer access when firmware
supplies invalid log indices. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: sit: reload inner IPv6 header after GSO offloads
ipip6_tunnel_xmit() caches the inner IPv6 header pointer at function
entry and continues using it after iptunnel_handle_offloads().
For GSO skbs, iptunnel_handle_offloads() calls skb_header_unclone().
When the skb header is cloned, skb_header_unclone() can call
pskb_expand_head(), which may move the skb head. The pskb_expand_head()
contract requires pointers into the skb header to be reloaded after the
call.
If the later skb_realloc_headroom() branch is not taken, SIT uses the
stale iph6 pointer to read the inner hop limit and DS field. That can
read from a freed skb head after the old head's remaining clone is
released.
Reload iph6 after the offload helper succeeds and before subsequent
reads from the inner IPv6 header. Keep the existing reload after
skb_realloc_headroom(), since that branch can also replace the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Use krealloc_array() in dal_vector_reserve()
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
(cherry picked from commit 37668568641ccc4cc1dbca4923d0a16609dd5707) |
| In the Linux kernel, the following vulnerability has been resolved:
udf: reject descriptors with oversized CRC length
udf_read_tagged() skips CRC verification when descCRCLength +
sizeof(struct tag) exceeds the block size. A crafted UDF image can
set descCRCLength to an oversized value to bypass CRC validation
entirely; the descriptor is then accepted based solely on the 8-bit
tag checksum, which is trivially recomputable.
Reject such descriptors instead of silently accepting them. A
legitimate single-block descriptor should never have a CRC length that
exceeds the block. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: release layout stid on setlease failure
nfs4_alloc_stid() publishes the new stid into cl->cl_stateids via
idr_alloc_cyclic() under cl_lock before returning to
nfsd4_alloc_layout_stateid(). When nfsd4_layout_setlease() then
fails, the error path frees the layout stateid directly with
kmem_cache_free() without ever calling idr_remove(), leaving the
IDR slot pointing at freed slab memory. Any subsequent IDR walker
(states_show, client teardown) dereferences the dangling pointer.
The correct teardown for an IDR-published stid is nfs4_put_stid(),
which removes the IDR slot under cl_lock, dispatches sc_free
(nfsd4_free_layout_stateid) to release ls->ls_file via
nfsd4_close_layout(), and drops the nfs4_file reference in its
tail.
A second issue blocks that switch: nfsd4_free_layout_stateid()
unconditionally inspects ls->ls_fence_work via
delayed_work_pending() under ls_lock, but
INIT_DELAYED_WORK(&ls->ls_fence_work, ...) currently runs only
after the setlease call. On the setlease-failure path the
destructor would touch an uninitialized delayed_work.
nfsd4_alloc_layout_stateid()
nfs4_alloc_stid() /* idr_alloc_cyclic under cl_lock */
nfsd4_layout_setlease() /* fails */
nfs4_put_stid()
nfsd4_free_layout_stateid()
delayed_work_pending(&ls->ls_fence_work) /* needs INIT */
nfsd4_close_layout() /* nfsd_file_put(ls->ls_file) */
put_nfs4_file()
Fix by hoisting the ls_fenced / ls_fence_delay / INIT_DELAYED_WORK
initialization above the nfsd4_layout_setlease() call, and replace
the manual nfsd_file_put + put_nfs4_file + kmem_cache_free cleanup
with a single nfs4_put_stid(stp). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Ensure hugepage is in by slot before checking max mapping level
When recovering hugepages in the shadow MMU, verify that the base gfn of
the shadow page is actually contained within the target memslot, *before*
querying the max mapping level given the shadow page's gfn. Failure to
pre-check the validity of the gfn can lead to an out-of-bounds access to
the slot's lpage_info (which typically manifests as a host #PF because the
lpage_info is vmalloc'd) if the guest creates a hugepage mapping (in its
PTEs) that extends "below" the bounds of a memslot.
When faulting in memory for a guest, and the size of the guest mapping is
greater than KVM's (current) max mapping, then KVM will create a "direct"
shadow page (direct in that there are no gPTEs to shadow, and so the target
gfn is a direct calculation given the base gfn of the shadow page). The
hugepage recovery flow looks for such direct shadow pages, as forcing 4KiB
mappings when dirty logging generates the guest > host mapping size case.
When the 4KiB restriction is lifted, then KVM can replace the shadow page
with a hugepage.
But if KVM originally used a smaller mapping than the guest because the
range of memory covered by the guest hugepage exceeds the bounds of a
memslot, then KVM will link a direct shadow page with a gfn that is outside
the bounds of the memslot being used to fault in memory. The rmap entry
added for the leaf mapping is correct and within bounds, but the gfn of the
leaf SPTE's parent shadow page will be out of bounds.
BUG: unable to handle page fault for address: ffffc90000806ffc
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 1002a7067 PMD 10612f067 PTE 0
Oops: Oops: 0000 [#1] SMP
CPU: 13 UID: 1000 PID: 757 Comm: mmu_stress_test Not tainted 7.1.0-rc1-48ce1e26eace-x86_pir_to_irr_comments-vm #341 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_mmu_max_mapping_level+0x79/0x2b0 [kvm]
Call Trace:
<TASK>
kvm_mmu_recover_huge_pages+0x21b/0x320 [kvm]
kvm_set_memslot+0x1ee/0x590 [kvm]
kvm_set_memory_region.part.0+0x3a1/0x4d0 [kvm]
kvm_vm_ioctl+0x9bf/0x15d0 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb7/0xbb0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f21c0f1a9bf
</TASK>
Don't bother pre-checking the bounds of the potential hugepage, i.e. don't
check that e.g. sp->gfn + KVM_PAGES_PER_HPAGE(sp->role.level + 1) is also
within the memslot, as the checks performed by kvm_mmu_max_mapping_level()
are a superset of the basic bounds checks. I.e. pre-checking the full
range would be a dubious micro-optimization. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_nat_sip: rewind offset when NAT shrinks the packet
sashiko says:
If map_addr() changes the packet length, such as when the public NAT IP
string is shorter or longer than the internal IP, coff will still point to
the offset relative to the pre-mangled packet.
If the packet shrinks, coff could overshoot the correct position,
potentially causing the next ct_sip_parse_header_uri() call to silently
skip bytes and miss subsequent Contact headers. Could this lead to a
failure to NAT those subsequent headers and leak internal network details? |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: trf7970a: power down on startup RX gain failure
trf7970a_startup() powers up the device before applying the optional RX
gain reduction. If the register read or write fails, it returns without
undoing that power-up. Probe's unwind only drops the separate regulator
references acquired by probe, leaving the additional VIN enable from
startup unbalanced. The system resume caller also has no power-down on
this error.
Call trf7970a_power_down() before returning the RX gain error to deassert
the enable GPIOs, release the startup VIN reference and restore the
powered-off state. Runtime PM has not been enabled yet, so the full
shutdown helper is not appropriate here. Preserve the original SPI error.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: catc: bound the RX packet length in catc_rx_done()
catc_rx_done() walks a multi-packet URB, reading a two-byte length from
each packet header. Its bound, pkt_len > urb->actual_length, ignores the
header offset and compares against the whole transfer rather than the
bytes left from pkt_start, so a crafted packet header makes
skb_copy_to_linear_data() read past the buffer.
A length below ETH_HLEN is also accepted, including zero, and
eth_type_trans() then reads a MAC header from the uninitialised tailroom
of a shorter skb. The is_f5u011 branch takes its length straight from
the transfer, so a zero-length URB reaches the same path.
Track the bytes remaining from the current packet, and reject a header
that does not fit, a length past what is left, and a length below an
Ethernet header.
A transfer shorter than an Ethernet header, including a zero-length one,
previously became a runt skb passed to netif_rx() and counted as
received; it is now counted in rx_length_errors and ends the walk. |
| In the Linux kernel, the following vulnerability has been resolved:
net: atl1c: fix soft lockup on out-of-range tpd_cons read
The hardware can report an out-of-range tpd_cons (seen as 0xffff)
while the PCIe link/MAC is resetting. An out-of-range value can
never be reached and the loop below would spin forever. To avoid
a soft lockup treat it as "nothing new to clean" instead.
Reproduced on two machines, same NIC (Qualcomm Atheros AR8151 v2.0,
4-port), triggered by rebooting a Mikrotik CCR2004 PCIe card that
the ports are directly linked to:
- Ubuntu 26.04.1 LTS, kernel 7.0.0-31-generic. The link-flap
precursor, before the lockup was captured with a full trace
elsewhere:
atl1c 0000:05:00.0 enp5s0f0: NETDEV WATCHDOG: CPU: 4: transmit queue 2 timed out 489984 ms
atl1c 0000:05:00.0: MAC state machine can't be idle since disabled for 10ms second
atl1c 0000:05:00.0: atl1c: enp5s0f0 NIC Link is Up<65535 Mbps Full Duplex>
65535 (0xffff) here is the same value tpd_cons reads back once the
loop below gets stuck.
- Proxmox VE, kernel 7.0.14-11-pve. Same NIC/trigger, this time
caught by the soft lockup watchdog with a full stack trace:
watchdog: BUG: soft lockup - CPU#12 stuck for 354s! [napi/eth%d-0:329]
CPU: 12 UID: 0 PID: 329 Comm: napi/eth%d-0 Tainted: P O L 7.0.14-11-pve #1 PREEMPT(lazy)
RIP: 0010:atl1c_clean_tx+0x142/0x2d0 [atl1c]
Call Trace:
<TASK>
__napi_poll+0x32/0x1e0
napi_threaded_poll_loop+0x286/0x2e0
napi_threaded_poll+0xfd/0x140
kthread+0xf7/0x130
ret_from_fork+0x2da/0x3a0
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vfio-ap: fix KVM GISC and page leak when queue removed from host config
Three related problems exist in the handling of KVM interrupt and page
resources when a queue is removed from the host's AP configuration
while assigned to a mediated device (mdev).
Problem 1:
~~~~~~~~~
AP_RESPONSE_Q_NOT_AVAIL not handled in vfio_ap_mdev_reset_queue()
When the AP bus removes a queue device whose adapter or domain has
been removed from the host's AP configuration,
vfio_ap_mdev_remove_queue() is called. If the queue is still in the
host's AP configuration at that point, it calls
vfio_ap_mdev_reset_queue(), which issues a PQAP(ZAPQ). Since the
adapter is already gone from the host configuration, ap_zapq() returns
AP_RESPONSE_Q_NOT_AVAIL (0x01). This response code is not handled in
vfio_ap_mdev_reset_queue()'s switch statement and falls through to
the default case, which issues a WARN but does not call
vfio_ap_free_aqic_resources(). As a result, if IRQ handling was
enabled for the queue by the guest, the KVM GISC registration and
the pinned guest page holding the notification indicator byte (NIB)
are both leaked.
This is fixed by adding AP_RESPONSE_Q_NOT_AVAIL to the same case as
AP_RESPONSE_DECONFIGURED and AP_RESPONSE_CHECKSTOPPED in
vfio_ap_mdev_reset_queue(). Like those response codes, Q_NOT_AVAIL
indicates the queue is not operational and no further reset attempts
are possible; the correct action is to free the IRQ resources
immediately.
Problem 2:
~~~~~~~~~
AP_RESPONSE_Q_NOT_AVAIL not handled in apq_status_check()
In vfio_ap_mdev_reset_queue(), there are four cases that indicate a queue
reset has not yet completed, in which case apq_reset_check() is queued to
a work queue to verify completion of the reset operation. This function
uses the PQAP(TAPQ) function to get the queue's status and calls
apq_status_check() to verify whether the reset has completed, failed or
needs to be executed again. As described in Problem #1 above,
apq_reset_check() does not specifically check for AP_RESPONSE_Q_NOT_AVAIL,
thereby potentially leaking KVM GISC registration and the pinned guest page
holding the NIB.
This is fixed by adding a case statement for AP_RESPONSE_Q_NOT_AVAIL to
apq_status_check() and returning -ENODEV for that case. The caller,
apq_reset_check() will then check for this return code and call
vfio_ap_free_aqic_resources() to prevent the leak.
Problem 3:
~~~~~~~~~
vfio_ap_free_aqic_resources() leaks saved_isc when kvm is NULL
vfio_ap_free_aqic_resources() guards the call to
kvm_s390_gisc_unregister() with:
if (q->saved_isc != VFIO_AP_ISC_INVALID &&
!WARN_ON(!(q->matrix_mdev && q->matrix_mdev->kvm)))
If matrix_mdev->kvm is NULL -- which can happen when
vfio_ap_mdev_unset_kvm() has already run and cleared kvm before a
subsequent cleanup path reaches this function -- the WARN_ON fires
and the entire block is skipped. This leaves q->saved_isc set to a
non-invalid value, creating a potential double-free on any subsequent
call to this function.
When kvm is NULL the KVM guest is already torn down, so
kvm_s390_gisc_unregister() need not and cannot be called; however,
q->saved_isc must always be cleared. Fix this by separating the
kvm_s390_gisc_unregister() call from the q->saved_isc reset. The
WARN_ON now guards only the genuinely impossible case of matrix_mdev
being NULL. A NULL kvm is handled gracefully by skipping only the
unregister call, and q->saved_isc = VFIO_AP_ISC_INVALID is set
unconditionally whenever saved_isc was not already invalid.
Additionally, add an else clause to the host-config check in
vfio_ap_mdev_remove_queue() to call vfio_ap_free_aqic_resources()
directly when the queue is not in the host's AP configuration. This
serves as a backstop: when the AP bus fires the driver .remove
callback after an adapter is removed from the host config, the queue
is by definition no longer addressable, so vfio_ap_mdev_reset_queue
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Keep internal commands dispatchable during error handling
Commit 08b12cda6c44 ("scsi: ufs: core: Switch to scsi_get_internal_cmd()")
switched UFS internal commands to allocate requests on
hba->host->pseudo_sdev->request_queue, which shares the host tagset with
regular LUNs.
During error recovery, ufshcd_err_handling_prepare() calls
blk_mq_quiesce_tagset(&hba->host->tag_set), marking all queues in the
tagset as quiesced, including pseudo_sdev->request_queue. When
ufshcd_verify_dev_init() subsequently issues internal commands (e.g. NOP
OUT UPIU) via blk_execute_rq(), blk_mq_run_hw_queue() skips running the
quiesced queue, resulting in an unrecoverable circular wait deadlock.
Keep quiescing the tagset and unquiesce the pseudo SCSI device on top of
that, so internal commands stay dispatchable while the logical units remain
quiesced. Re-quiesce the pseudo device before unquiescing the tagset so
that quiesce_depth stays balanced.
Clock scaling and ufshcd_pause_command_processing() are unaffected: they
keep quiescing the whole tagset, internal commands included. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: drop truncated I/RR/RNR PDUs in nfc_llcp_recv_hdlc()
nfc_llcp_recv_hdlc() reads the sequence byte skb->data[2], via
nfc_llcp_ns()/nfc_llcp_nr(), before any length check. The receive path
only guarantees the two-byte LLCP header -- __nfc_llcp_recv() checks it
with pskb_may_pull() and nfc_llcp_recv_agf() admits two-byte inner PDUs
-- so a two-byte I, RR or RNR PDU reads one byte of uninitialised skb
tailroom. The byte becomes N(R)/N(S); a peer can already set those with
a well-formed PDU, so this is acting on uninitialised memory, not new
peer control.
Guard the read with pskb_may_pull(), as commit 95674f506c63 ("nfc: llcp:
reject PDUs shorter than the LLCP header") did for the two-byte header,
so the sequence byte is present and linear before it is read. RR and RNR
PDUs are LLCP_HEADER_SIZE + LLCP_SEQUENCE_SIZE bytes and an I PDU is
longer, so no valid frame is rejected; a truncated PDU is malformed, so
return without a DM reply. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: fix use-after-free in nfc_get_local_general_bytes
Commit 6709d4b7bc2e ("net: nfc: Fix use-after-free caused by
nfc_llcp_find_local") attempted to fix a use-after-free (UAF) issue by
invoking nfc_llcp_local_put(local) after accessing local->gb. However,
if the reference count drops to zero, local is freed immediately,
leading to a use-after-free when callers access the returned pointer.
Alternative approaches using dynamic allocation (e.g. kmemdup) introduced
memory leaks because callers consistently treat the returned pointer as
borrowed memory.
Fix this properly by refactoring nfc_llcp_general_bytes() and
nfc_get_local_general_bytes() to accept a caller-provided output buffer
(out_gb) and its maximum length (gb_max_len). The general bytes are
safely copied into out_gb before calling nfc_llcp_local_put(local),
ensuring safe lifetime management without ownership transfer complications.
Update all callers across drivers (microread, pn533, pn544, st21nfca,
digital_dep, and nci) to provide their own destination buffers and pass
them to nfc_get_local_general_bytes(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: atl1e: fix soft lockup on out-of-range hw_next_to_clean read
Same issue as atl1c (see the first commit in this series, "net:
atl1c: fix soft lockup on out-of-range tpd_cons read"): the hardware
can report an out-of-range hw_next_to_clean (seen as 0xffff) while
the PCIe link/MAC is resetting. An out-of-range value can never be
reached and the loop below would spin forever. Treat it as "nothing
new to clean" instead. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Don't WARN on an unknown VM ioctl in protected mode
kvm_pkvm_ioctl_allowed() WARNs when kvm_get_cap_for_kvm_ioctl() doesn't
find the ioctl number in vm_ioctl_caps[], and kvm_arch_vm_ioctl() calls
it for every number the generic code doesn't handle, so
ioctl(vm_fd, 0xdeadbeef) from userspace taints a pKVM host and panics it
under panic_on_warn. The lookup is fed userspace input: return false,
and userspace gets the -EINVAL kvm_arch_vm_ioctl() returns for that
number on a host without pKVM. |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: fix dma_alloc_coherent() leak on macb_alloc() error paths
Fix 3 leaks in macb_alloc() error paths:
- Tx buffer allocated but crossing a 4G boundary: Tx leaked.
- Rx buffer allocation fails: Tx leaked.
- Rx buffer allocated but crossing a 4G boundary: Tx & Rx leaked.
This is because our error handling calls macb_free(bp) which in turn
frees the buffers stored in bp->queues[0], but nothing has been stored
in there. Fix by storing allocated buffers into bp->queues[0] ASAP. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: hid-oxp: use cancel_delayed_work_sync() in remove
oxp_hid_remove() uses cancel_delayed_work() for all three delayed work
items. cancel_delayed_work() only dequeues a pending work item without
waiting for a currently executing callback to finish. If any of the
work callbacks (oxp_rgb_queue_fn, oxp_btn_queue_fn, oxp_mcu_init_fn) is
running at the time of removal, the callback continues executing
concurrently with hid_hw_close() and hid_hw_stop(), accessing the HID
device after it has been closed and stopped.
Use cancel_delayed_work_sync() instead to ensure that any in-progress
work callback completes before device teardown proceeds. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: validate device-supplied DMA indices
In btintel_pcie_msix_rx_handle(), the driver processes RX completion
descriptors (urbd1) written by the PCIe device into DMA-coherent memory.
urbd1->frbd_tag (a 16-bit field fully controlled by the device firmware
via DMA) is used directly as an array index into rxq->bufs[] without any
bounds check. rxq->bufs[] has only BTINTEL_PCIE_RX_DESCS_COUNT (64)
entries, while frbd_tag can be any value 0-65535. A malicious or
malfunctioning device can write an out-of-range frbd_tag, causing the
driver to dereference an out-of-bounds data_buf pointer.
Additionally, cr_hia is read from a DMA-shared index array also writable
by the device; if the device sets cr_hia >= rxq->count, the while-loop
never terminates because cr_tia is wrapped via modulo rxq->count and can
never equal an out-of-range cr_hia.
Add bounds validation for cr_hia and frbd_tag in the RX path, and cr_hia
in the TX path. Log invalid values with bt_dev_err before returning. |
