| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The nRF link-layer receive paths of the open-source Bluetooth LE Controller did not validate the on-air LENGTH field of a received PDU against the maximum receive length that was used to program the radio. isr_rx_pdu() in subsys/bluetooth/controller/ll_sw/nordic/lll/lll_conn.c enqueued any non-empty data PDU after only the sequence-number and (for encrypted links) MIC checks, and the corresponding isr_rx() handlers in lll_central_iso.c, lll_peripheral_iso.c, lll_sync_iso.c and lll_scan_aux.c did the same for ISO and extended-advertising PDUs. The nRF radio stores the received header verbatim and truncates only the payload at PCNF1.MAXLEN, so a frame declaring more octets than were configured leaves a node buffer whose len field describes more data than the buffer holds.
An attacker within radio range that can emit a hand-crafted link-layer PDU — for a connection, any peer that establishes an unencrypted LE connection to a connectable advertiser; for CONFIG_BT_CTLR_SYNC_ISO, any broadcaster the device is synchronised to — can set the length byte up to 255 while the controller has programmed a much smaller maximum (lll->dle.eff.max_rx_octets, which is 27 until a Data Length Update, or the negotiated cis_lll->rx.max_pdu). No pairing, authentication or user interaction is required. On encrypted links the CCM MIC check normally rejects such a frame first, so the exposure is on unencrypted traffic, which is why the added check is placed after decryption.
The unchecked length reaches hci_acl_encode() in subsys/bluetooth/controller/hci/hci.c, which performs net_buf_add(buf, pdu_data->len) followed by a memcpy() of that many bytes out of the node_rx pool element. Because CONFIG_BT_CTLR_DATA_LENGTH_MAX and CONFIG_BT_BUF_ACL_RX_SIZE both default to 27, this is an out-of-bounds read of up to roughly 228 bytes past the received PDU and a corresponding out-of-bounds write past the HCI ACL buffer into neighbouring buffers of the same pool; the tailroom test in net_buf_simple_add() is only enforced when CONFIG_NET_BUF_HARDENING (or CONFIG_ASSERT) is enabled. On the ISO paths the same unchecked length makes isoal_rx_append_to_sdu() read past the ISO node buffer and emit adjacent controller RAM to the host as ISO data. The practical result is remote memory corruption and controller crashes, plus disclosure of controller memory into the host data path.
The fix rejects any received PDU whose length exceeds the value that was used to configure the radio reception. Note that lll_sync.c (periodic advertising sync reception) was not changed and still enqueues received PDUs without an equivalent bound. |
| The entropy-device random number generator in subsys/random/random_entropy_device.c returned early with -ENODEV from rand_get() as soon as device_is_ready() failed, before reaching the non-cryptographic system-timer fallback further down the same function. Because z_impl_sys_rand_get() returns void and discards that error — and the public sys_rand_get() syscall is itself declared void, so it cannot report failure — the caller's output buffer was left untouched and its previous contents were handed back as random data. The thin wrappers make this a plain uninitialized read: sys_rand32_get() declares uint32_t ret;, calls sys_rand_get(&ret, sizeof(ret)) and returns ret.
The "not ready" state is a normal runtime condition rather than a fault. Entropy drivers initialise at PRE_KERNEL_1 with CONFIG_ENTROPY_INIT_PRIORITY (default 50), so any earlier initialiser — kernel objects run at priority 30 — observes an unready device; the sibling generator subsys/random/random_xoshiro128.c and z_early_rand_get() in kernel/init.c both already carried an explicit timer fallback for exactly this case. The state is also permanent for the boot when an entropy driver's init hook fails, which several in-tree drivers can do on real hardware (entropy_stm32 on an RNG clock configuration error, entropy_psa_crypto when psa_crypto_init() fails, entropy_nrf_cracen, entropy_esp32, entropy_virtio).
When this occurs, every non-cryptographic random value in the system is either a constant or stale memory. coap_next_token() in subsys/net/lib/coap/coap.c fills a static buffer, so every CoAP token becomes the same .bss constant; tcp_init_isn() in subsys/net/ip/tcp.c returns an uninitialized stack word as the TCP initial sequence number; DHCPv4/DHCPv6 transaction IDs, WebSocket masking keys and RTP SSRCs are similarly degraded, and arch/arm64/core/pac.c derives per-thread Pointer Authentication keys from the same source. Where the bytes are transmitted directly — SSH packet padding, the netmidi2 session nonce, a DTLS connection ID on builds without CONFIG_CSPRNG_ENABLED — stale caller stack or heap contents are disclosed on the wire.
The fix initialises ret to -ENODEV and only calls entropy_get_entropy() when the device is ready, so the not-ready case now falls through to the timer fallback and the buffer is always written. The cryptographically secure path is unchanged: sys_csrand_get() still propagates the error to the caller and never silently degrades. An attacker cannot induce the unready state, but can observe and exploit the resulting non-random values remotely on an affected device. |
| The Mbed TLS crypto shim driver in drivers/crypto/crypto_mbedtls_shim.c drives PSA multipart cipher and AEAD operations. In mbedtls_cbc() and mbedtls_aead(), every error path after a successful psa_cipher_encrypt_setup() / psa_aead_decrypt_setup() returned directly without calling psa_cipher_abort() / psa_aead_abort(). Because the abort is the only thing that reaches mbedtls_cipher_free(), each failed operation permanently leaked the heap-allocated mbedtls_aes_context (roughly 288 bytes) that setup had allocated from Mbed TLS's fixed static heap (_mbedtls_heap[CONFIG_MBEDTLS_HEAP_SIZE], default 512 bytes). With CONFIG_PSA_CRYPTO_PROVIDER_TFM the leaked object is instead a finite secure-partition multipart-operation slot.
The failure is chosen by an unauthenticated attacker. With CONFIG_NET_L2_IEEE802154_SECURITY backed by this driver, ieee802154_decrypt_auth() in subsys/net/l2/ieee802154/ieee802154_security.c invokes cipher_ccm_op() on every received secured frame, with no authentication ahead of the MIC check. A device in radio range can transmit a stream of syntactically valid 802.15.4 frames carrying a bogus MIC; each one makes psa_aead_verify() fail and leaks a block. The CBC path is reachable the same way through the OSDP secure channel, where CONFIG_OSDP_SC_ENABLED selects this shim and osdp_encrypt() / osdp_decrypt() leave out_buf_max unset, so every operation fails inside psa_cipher_update().
Exhausting the Mbed TLS heap — which the default configuration reaches after a couple of failed operations, and any realistic configuration reaches in well under a second of frames — makes all subsequent mbedtls_calloc() calls fail. Every later cryptographic operation in the image then fails permanently, including link-layer security and any TLS/DTLS sharing the same heap, until the device is rebooted. There is no memory corruption or information disclosure: frames with an invalid MIC are still rejected, so the impact is limited to availability.
The fix routes all post-setup failures in mbedtls_cbc() and mbedtls_aead() through a common error: label that calls the matching PSA abort before returning. Setup failures need no change, since the PSA core aborts the operation itself when setup fails. |
| The flash_copy() system call is verified by z_vrfy_flash_copy() in drivers/flash/flash_util.c. On builds with CONFIG_USERSPACE enabled, this handler is the kernel-side trust boundary for a user-mode caller. Prior to the fix it validated only the output buffer (K_SYSCALL_MEMORY_WRITE) and passed the two struct device * arguments, src_dev and dst_dev, directly into the implementation without any object validation — unlike every sibling flash syscall, which guards its device pointer with K_SYSCALL_DRIVER_FLASH.
A user-mode thread fully controls the values of src_dev/dst_dev and the contents of its own address space. The implementation z_impl_flash_copy() dereferences these pointers and calls through their driver-API function tables (e.g. api->get_parameters(dst_dev), flash_read(src_dev, ...), flash_write(dst_dev, ...)). By supplying a pointer to a forged struct device whose api table contains attacker-chosen function pointers, an unprivileged thread can cause the kernel to call arbitrary code in supervisor mode; passing any arbitrary or invalid address otherwise yields a kernel crash or out-of-bounds read.
The result is a local privilege escalation out of the userspace sandbox (with kernel denial-of-service and information disclosure as lesser outcomes). The fix adds K_SYSCALL_DRIVER_FLASH(src_dev, read) and K_SYSCALL_DRIVER_FLASH(dst_dev, write) to z_vrfy_flash_copy(), which verify each device is a registered flash-driver kernel object the calling thread is permitted to use before any dereference, closing the path completely. |
| The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio's RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len < 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped.
An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.
With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected. |
| The receive path of the NXP KW41Z IEEE 802.15.4 driver, kw41z_rx() in drivers/ieee802154/ieee802154_kw41z.c, computed the payload size as pkt_len = len - KW41Z_FCS_LENGTH in a uint8_t, where len is the frame length reported by the radio. The interrupt handler kw41z_isr() obtained that length from the RX_FRAME_LENGTH field of the ZLL IRQSTS register — a copy of the PHY header length byte of the frame received over the air — and only rejected the value zero. A reported length of one therefore underflowed to pkt_len == 255.
Because the packet is allocated with NET_AF_UNSPEC on a non-Ethernet L2, net_pkt_rx_alloc_with_buffer() does not clamp the request to the interface MTU; with the default fixed-size buffer pool (CONFIG_NET_BUF_FIXED_DATA_SIZE, CONFIG_NET_BUF_DATA_SIZE=128) the allocation succeeded as a chain of two fragments. The subsequent register-to-buffer copy loops write into the first fragment only, so 255 bytes were written into a 128-byte net_buf data block, overrunning it by up to 127 bytes into adjacent network-buffer-pool memory, and reading up to 128 bytes past the end of the radio's PKT_BUFFER_RX register array.
The length field originates from an unauthenticated frame transmitted by any device within 802.15.4 radio range, and is captured by the hardware at PHY-header time — before frame filtering has completed — while the handler samples it after clearing the interrupt status, so an attacker flooding frames with a length byte of one can drive the underflow. The impact is memory corruption in the shared receive buffer pool from interrupt context, most plausibly a crash or corruption of other packets' data; the overflowing bytes are radio register contents rather than attacker-authored data, which bounds the integrity impact.
The fix rejects any length below KW41Z_FCS_LENGTH and additionally verifies net_buf_tailroom() of the first fragment before the copy loops, which also covers the CONFIG_NET_L2_OPENTHREAD variant of the size computation. |
| The OCPP 1.6 client in subsys/net/lib/ocpp/ocpp.c reconstructs a session handle and PDU id from the uid field of a CALLRESULT message. In ocpp_process_server_msg() the code calls atoi(strtok_r(uid, "-", &tmp)) without checking the strtok_r return value. When the server-supplied uid is empty or contains no - delimiter, strtok_r() returns NULL and atoi(NULL) dereferences a NULL pointer, which is undefined behaviour.
The uid originates from network data: parse_rpc_msg() in subsys/net/lib/ocpp/ocpp_j.c JSON-parses a frame received from the OCPP central system over TCP/WebSocket and copies the server-controlled string into the local buffer. A malicious or compromised central system, or a man-in-the-middle on a non-TLS ws:// connection, can return a malformed uid to reach the defect. No authentication beyond the existing server connection (or MITM position) is required, and the reconstructed pointer is membership-validated by ocpp_session_is_valid(), so the impact is limited to the NULL dereference rather than arbitrary pointer use.
On Zephyr targets that trap access to address 0 (MMU/MPU platforms or CONFIG_NULL_POINTER_EXCEPTION_DETECTION), the dereference faults inside the OCPP reader thread and invokes the fatal handler, producing a remote denial of service of the charge point; on bare targets where address 0 is readable the call returns 0 and is benign, so the impact is availability-only and platform-conditional.
The applied fix guards only the first atoi(); the second strtok_r(NULL, "-", &tmp) followed by pdu = atoi(buf) in the same function remains unguarded and the identical NULL dereference is still reachable from the same network input when the uid has a first token but no second --delimited token. A complete fix should validate the second token as well. |
| Zephyr's Precision Time Protocol receive handler ptp_msg_post_recv() in subsys/net/lib/ptp/msg.c takes the 4-bit message type straight off the wire via ptp_msg_type() (msg->header.type_major_sdo_id & 0xF, range 0-15) and uses it to index the msg_size[] table. That table only defines entries up to PTP_MSG_MANAGEMENT (0xD), giving it ARRAY_SIZE == 14. Before the fix there was no upper-bound check, so the undefined types 0xE and 0xF indexed one or two int slots past the end of the array — an out-of-bounds read of adjacent read-only data.
The out-of-bounds value is then reused as a length: it gates msg_size[type] > cnt, and when it is small or negative it makes cnt - msg_size[type] a large positive budget passed to msg_tlv_post_recv(), whose TLV loop then walks the message suffix past the received bytes, performing further out-of-bounds reads and in-place byte-swap writes on memory beyond the message slab.
The defect is reached directly from the network: ptp_port_event_gen() in subsys/net/lib/ptp/port.c reads a PTP frame with ptp_transport_recv() and calls ptp_msg_post_recv() with the attacker-chosen type. PTP uses UDP multicast or raw Ethernet (0x88F7) and is unauthenticated, so any host on the same link can trigger the indexing on a CONFIG_PTP-enabled node with no preconditions.
The reliably reproducible impact is a denial of service (fault/crash); a limited memory-corruption path exists but depends on the build-specific value adjacent to msg_size[], which the attacker cannot tune. The fix rejects type >= ARRAY_SIZE(msg_size) with -EBADMSG before any indexing. |
| The Zephyr kernel validates the k_thread_join() and k_thread_abort() system calls (declared __syscall in include/zephyr/kernel.h) through thread_obj_validate() in kernel/thread.c. Its default switch branch is the access-denied path, taken when k_object_validate() returns -EPERM (the calling user thread was never granted access to the target thread object) or -EBADF (the supplied pointer is not a registered kernel object of the right type). That branch invoked K_OOPS(K_SYSCALL_VERIFY_MSG(ret, "access denied")), but K_SYSCALL_VERIFY_MSG treats a true expression as success; the non-zero error code ret therefore read as "verified OK", the kernel oops was never raised, and control fell through to CODE_UNREACHABLE.
Because k_thread_join() and k_thread_abort() are system calls, an unprivileged user-mode thread (under CONFIG_USERSPACE) can reach this denial path directly by calling either syscall on a thread object it does not own. Instead of the offending thread being cleanly terminated, execution reaches __builtin_unreachable() while running in supervisor mode inside the syscall handler.
On Clang builds CODE_UNREACHABLE emits an illegal-instruction trap, so a user thread can deterministically crash the kernel — a locally triggerable denial of service that escapes the userspace sandbox. On GCC builds the path is undefined behavior: the compiler may drop the return-value handling for thread_obj_validate(), so it can return an undefined bool; if that is false, the caller proceeds into the real k_thread_join()/k_thread_abort() implementation for a thread the user was never authorized to access, an access-control bypass.
The fix changes the verification expression to ret == 0, so a denied (non-zero) result now correctly raises K_OOPS and terminates the offending caller. |
| The ARM PL011 UART driver in drivers/serial/uart_pl011.c fails to acknowledge receive error interrupts. On the PL011, the framing, parity, break, and overrun error interrupts (PL011_IMSC_ERROR_MASK) are cleared only by writing the interrupt-clear register UARTICR; reading the data register clears the RX interrupt and the per-byte RSR status but not the error interrupt status in MIS. The interrupt service routine pl011_isr() acknowledged only the CTS modem-status interrupt and never wrote icr for the error bits, so an asserted error interrupt remains pending after the ISR returns.
When an application enables error-interrupt reporting via the public uart_irq_err_enable() API, an attacker who controls the serial peer can deterministically assert these error bits by injecting line errors on the RX line — a baud/stop-bit mismatch or mid-character break (framing/break error), a flipped parity bit (parity error), or FIFO flooding (overrun error). Because the error interrupt is never cleared, the interrupt line stays asserted and the CPU re-enters pl011_isr() immediately and indefinitely, producing an interrupt-storm livelock from which the core makes no forward progress.
The impact is an availability-only denial of service (permanent hang), reachable from an external or removable UART peer. Exploitation is gated by configuration: the error interrupt is off by default and no in-tree subsystem enables it, so only applications that explicitly call uart_irq_err_enable() on a PL011-based, interrupt-driven port are affected. The fix makes pl011_isr() acknowledge the pending error bits via uart->icr, breaking the loop, and additionally clears the latched RSR status in pl011_err_check(). |
| The HL7800 cellular modem driver's +CGCONTRDP: response handler on_cmd_atcmdinfo_ipaddr() in drivers/modem/vendor_standalone/hl7800.c parses the PDP-context dynamic parameters (local address, subnet mask, gateway, and DNS servers) that the cellular network assigns to the device. The response is linearized into a 256-byte stack buffer, after which each address field length is computed from comma/. delimiter positions in the network-supplied data and used directly as the length argument to strncpy() into the fixed 64-byte stack buffer temp_addr_str (and the 16-byte iface_ctx.dns_v4_string).
Because the field length is derived from attacker-controlled delimiter positions and was not bounded against the destination buffer, a single field can be far larger than 64 bytes. A malicious or impersonated cellular network (for example a rogue base station) can return a crafted +CGCONTRDP response with an overlong address field, causing strncpy() to write past temp_addr_str on the modem worker thread's stack, plus an out-of-bounds NUL write at temp_addr_str[addr_len].
No device-side privileges or user interaction are required: the device itself issues the AT+CGCONTRDP=1 query during normal network attach and parses whatever the network returns. The overflow corrupts adjacent stack memory in supervisor context, yielding at minimum a remotely triggerable crash and potentially control-flow hijacking on targets without stack protection.
The fix bounds every field length against its destination buffer (temp_addr_str and dns_v4_string) before each copy, rejecting overlong fields. |
| The MCTP-over-I2C+GPIO target binding in subsys/pmci/mctp/mctp_i2c_gpio_target.c emulates a small pseudo-register file, where the bus controller first writes a register number and then writes or reads payload bytes. The selected register (b->reg_addr) and the data-phase flag (b->rxtx) were never cleared when the controller issued an I2C STOP, so after a completed transfer the target still had a data register selected while the packet buffer that register refers to had already been consumed and set to NULL by mctp_i2c_gpio_target_stop().
A controller on the bus can re-enter the same branch of mctp_i2c_gpio_target_stop() with a NULL buffer using two ordinary transactions and no authentication: first a normal packet write to MCTP_I2C_GPIO_RX_MSG_ADDR followed by STOP (which delivers and frees b->rx_pkt), then a bare read transaction followed by STOP. The failing read_requested() call leaves the stale state untouched and the I2C driver still delivers the STOP callback, which then calls mctp_bus_rx() with a NULL packet. The symmetric case exists on the transmit side, where the stale MCTP_I2C_GPIO_TX_MSG_ADDR selection dereferences b->tx_pkt->end after b->tx_pkt has been cleared and additionally signals b->tx_complete a second time, causing the next outbound packet to be dropped.
The dereference happens in the I2C target interrupt handler, so on any target that traps accesses to address 0 the result is a fatal exception and a device reset or halt — a denial of service inflicted by any device able to act as controller on the shared management bus (for example compromised firmware on a peer MCTP endpoint or on the BMC). On parts where address 0 is readable, the impact degrades to a malformed packet buffer being handed to the MCTP stack and lost transmit packets. No attacker-controlled value is written and no confidentiality or integrity boundary is crossed.
The fix resets b->reg_addr to MCTP_I2C_GPIO_INVALID_ADDR and clears b->rxtx at every STOP, so a new register must be selected before any data phase can run again. Only builds that opt into the experimental CONFIG_MCTP subsystem with CONFIG_MCTP_I2C_GPIO_TARGET=y are affected. |
| The Bluetooth Classic Hands-Free Profile HF role in subsys/bluetooth/host/classic/hfp_hf.c does not release the AT command buffers that are still queued on hf->tx_pending when the RFCOMM DLC goes down. hfp_hf_disconnected() only cancelled the work items and cleared hf->acl, and no other code path ever dequeues those buffers, so each one is permanently lost from the fixed hf_pool (CONFIG_BT_MAX_CONN + 1 buffers, i.e. two in the default configuration). The same function also left BT_HFP_HF_FLAG_CONNECTED set, and hfp_hf_create() wiped the object with memset() as soon as hf->acl was NULL, without checking whether hf->work, hf->slc_work or hf->deferred_work was still pending or running.
The remote Audio Gateway peer controls the trigger end to end and needs no application involvement: an unsolicited +BCS: 1 response makes bcs_handle() call bt_hfp_hf_select_codec() and queue an AT+BCS buffer, which cannot be transmitted while BT_HFP_HF_FLAG_RX_ONGOING is set, and an immediately following RFCOMM DISC strands that buffer. Repeating the connect / +BCS / disconnect cycle a couple of times empties hf_pool for good.
With the pool exhausted, HFP command sending fails permanently, and because hfp_hf_send_cmd() allocates with K_FOREVER (bt_rfcomm_create_pdu() → bt_conn_create_pdu()) from the Bluetooth RX context — where that timeout is not downgraded to K_NO_WAIT — one further +BCS from the peer parks the Bluetooth RX thread inside net_buf_alloc() with no possible waker, halting all HCI event processing until the device is rebooted. Separately, reusing the HF slot while a work handler was still queued or running allowed memset() to wipe live k_work items out from under the system workqueue, corrupting shared kernel workqueue state. Exploitation requires an established HFP session (for SSP devices L2CAP enforces authentication before the RFCOMM channel is reachable) and a build with CONFIG_BT_HFP_HF enabled. |
| Zephyr's IPv6 forwarding path re-sent routed unicast packets without ever decrementing the IPv6 hop limit. Both routing branches of ipv6_route_packet() (subsys/net/ip) were affected: the explicit-route path (net_route_packet()) and the on-link cross-interface path (net_route_packet_if()). Each set the packet forwarding flag and called net_send_data() with the hop limit untouched and no expiry check.
Per RFC 8200 the hop-limit decrement is the mechanism that bounds packet lifetime and terminates routing loops; without it, a device acting as an IPv6 router relays looping packets indefinitely. An on-path attacker who can induce or exploit a transient L3 loop turns it into a permanent forwarding storm, causing CPU/bandwidth resource exhaustion (availability DoS) on the forwarder and adjacent links; path-discovery and loop diagnostics that rely on hop-limit expiry are also defeated.
Affected configurations. In every affected release the forwarding path is reached via CONFIG_NET_ROUTE (enabled by default when CONFIG_NET_IPV6_NBR_CACHE is set), together with CONFIG_NET_ROUTING for cross-interface routing. Note that CONFIG_NET_IPV6_FORWARDING and CONFIG_NET_IPV4_FORWARDING — which appear in the fix and in this advisory's evidence notes — were introduced after v4.4.0, when the routing options were split and renamed; they do not exist in any affected release. When auditing a v4.4.1-or-earlier configuration, look for CONFIG_NET_ROUTE and CONFIG_NET_ROUTING.
IPv4 is not affected in any release. The IPv4 forwarding path (net_route_ipv4_packet() in route_ipv4.c) was added after v4.4.0 and has never shipped in a release. Its TTL decrement and IPv4 header-checksum recomputation landed on main as part of the same fix, so the evidence notes below discuss it, but no released version is reachable by way of IPv4.
Affected releases are v1.8.0 through v4.4.1: v1.8.0 introduced net_route_packet() and v2.2.0 added net_route_packet_if(), and neither decremented the hop limit. v4.3.1 carries the explicit-route fix but not the on-link one, so it is affected as well. Fixed on main by 7d8f1afa7345 (explicit-route path) and 589eadc74efa (on-link path). |
| The Zephyr Bluetooth LE Audio Basic Audio Profile (BAP) unicast client mishandles peer-supplied ASE state notifications. In unicast_client_ep_qos_state() (subsys/bluetooth/audio/bap_unicast_client.c), the handler writes attacker-controlled QoS fields (interval, framing, phy, sdu, rtn, latency, pd) through the stream->qos pointer with only a stream != NULL guard. stream->qos is NULL for any stream that has been codec-configured via bt_bap_stream_config() but not yet added to a unicast group (it is set only by unicast_group_add_stream()).
A malicious or buggy remote ASCS server, to which the local device is connected as a BAP unicast client, can send a GATT notification announcing the ASE has entered the QoS Configured state while the local endpoint is still in the Codec Configured state — a transition the dispatcher explicitly permits — during that window, causing a write through a NULL pointer and a crash (denial of service). The data written is itself remote-controlled.
The defect shipped in v4.3.0 and v4.4.0 (and earlier). The fix re-points all BAP QoS storage to the always-valid embedded ep->qos struct, eliminating the NULL dereference. |
| Zephyr's IP socket recvmsg() implementation (subsys/net/lib/sockets/sockets_inet.c, insert_pktinfo()) validated the user-supplied ancillary (msg_control) buffer using only the payload length (msg->msg_controllen < pktinfo_len) before writing a full control message consisting of an aligned cmsg header plus the payload. Because the check omitted the cmsg header size, a control buffer whose length falls in the under-checked window (e.g. 16-27 bytes for IPv4 IP_PKTINFO on a 64-bit target, where a single element actually occupies 28 bytes) passes the guard yet causes a fixed-size out-of-bounds write of up to one cmsg header (~12 bytes) past the end of the buffer.
Under CONFIG_USERSPACE the recvmsg verifier allocates a kernel-heap copy of the control buffer sized to msg_controllen and runs the implementation against it, so the overflow corrupts kernel heap memory and is triggerable from an unprivileged userspace thread; in supervisor mode it corrupts the caller's buffer.
The path is reachable on a UDP/IP socket with IP_PKTINFO/IPV6_RECVPKTINFO (or hoplimit/timestamping) enabled when the application calls recvmsg() with an undersized control buffer and a datagram is received; part of the overwritten bytes (the destination IP in ipi_addr) is influenced by the received packet.
The fix makes the capacity check use NET_CMSG_SPACE(pktinfo_len) (aligned header + aligned data) and returns -ENOMEM when the buffer is too small. Affected: v3.6.0 through v4.4.0. |
| The Zephyr PL011 UART driver (drivers/serial/uart_pl011.c) contains an unbounded software loop in pl011_irq_tx_enable() that repeatedly invokes the interrupt-driven application callback while the TX interrupt mask bit (PL011_IMSC_TXIM) is set, to work around the controller's level-transition TX-interrupt behavior.
When CTS hardware flow control is enabled (devicetree hw-flow-control or runtime UART_CFG_FLOW_CTRL_RTS_CTS) and the wired serial peer de-asserts CTS, the controller stops draining the TX FIFO; pl011_fifo_fill() then returns 0 on every call while the application still has pending data and therefore never disables the TX interrupt. The loop condition never clears, so the thread that called uart_irq_tx_enable() (e.g. h4_send() in the Bluetooth HCI H4 driver) spins indefinitely, hanging the executing context and stalling the transport — a denial of service (CWE-835).
An attacker controlling the device attached to the UART's CTS line can trigger the hang by withholding CTS during transmission. Because that peer is the device wired to the UART — which may be a removable or external module (e.g. an off-board Bluetooth controller on the HCI H4 link) rather than a permanently-bonded on-PCB part — the attack vector is scored Adjacent (AV:A) rather than Physical; the security subcommittee should confirm the vector against the specific deployment. Impact is availability only; there is no memory-safety, confidentiality, or integrity consequence.
The vulnerable loop was introduced in commit b783bc8448ef (Feb 2025) and shipped in releases v4.1.0 through v4.4.0. The fix breaks out of the loop when CTS is blocking and arms the CTS modem-status interrupt to resume transmission when CTS re-asserts. |
| The can_add_rx_filter_msgq() system call installs a CAN RX filter whose callback (can_msgq_put() in drivers/can/can_common.c) is handed the caller's struct k_msgq * as user_data. The controller driver stores that raw pointer in its filter table and dereferences it from the RX path every time a matching frame arrives. The system call verifier z_vrfy_can_add_rx_filter_msgq() in drivers/can/can_handlers.c validated the queue only with K_SYSCALL_OBJ(), which is a point-in-time check of type, initialization and caller permission and says nothing about the object's lifetime.
On a build with CONFIG_USERSPACE=y and CONFIG_DYNAMIC_OBJECTS=y, an unprivileged user-mode thread that has been granted access to a CAN device can obtain a message queue whose lifetime it fully controls: k_object_alloc(K_OBJ_MSGQ) followed by k_msgq_alloc_init(). The lifetime of such an object is driven solely by its permission bitmask, and a pointer retained by the kernel is not represented there. After registering the filter, the thread calls k_object_release() — or simply terminates — and unref_check() frees the struct k_msgq storage while the CAN driver still holds the pointer.
The next matching CAN frame causes k_msgq_put() to run in supervisor context against freed memory that the attacker can have groomed with another kernel allocation: the frame payload is memcpy()d through the reused block's write_ptr, and the queue's wait_q (and poll_events under CONFIG_POLL) list nodes are manipulated. This yields kernel-heap corruption reachable from a user-mode thread, defeating the isolation CONFIG_USERSPACE is intended to provide; the same dangling pointer also arises benignly when an application thread exits without calling can_remove_rx_filter().
The fix validates the queue with K_SYSCALL_OBJ_STATIC(), which additionally rejects objects carrying K_OBJ_FLAG_ALLOC, so only statically defined queues (CAN_MSGQ_DEFINE()) may be registered from user mode. Supervisor-mode callers bypass the verifier and must themselves keep the queue valid until the filter is removed. |
| The Bluetooth host's GATT client passed the value of a received Handle Value Notification, Handle Value Indication or Multiple Handle Value Notification to bt_gatt_subscribe_params::notify callbacks using only the length derived from the received ATT PDU. bt_att_recv() in subsys/bluetooth/host/att.c validates only a minimum PDU length and does not enforce the negotiated ATT MTU, and the fixed ATT L2CAP channel in subsys/bluetooth/host/l2cap.c applies no rx.mtu check either, so the only ceiling was the ACL reassembly buffer CONFIG_BT_BUF_ACL_RX_SIZE. Values longer than the 512-octet maximum attribute length defined by the Bluetooth Core Specification (Vol 3, Part F, Section 3.2.9) could therefore be handed to subscribers that size their buffers to that documented limit.
A remote peer that a device has connected and subscribed to — a malicious, spoofed or compromised GATT server within radio range — triggers the flaw by sending a notification or indication whose value exceeds 512 octets on a subscribed handle. In the LE Audio unicast client this reaches a concrete out-of-bounds write: unicast_client_ep_notify() in subsys/bluetooth/audio/bap_unicast_client.c copies the notification into the 512-byte att_buf of struct unicast_client with net_buf_simple_add_mem() and no tailroom check whenever length equals bt_audio_get_max_ntf_size(), i.e. the negotiated ATT MTU minus three. notify_handler() in subsys/bluetooth/audio/bap_broadcast_assistant.c has the same shape. Reaching the overflow requires a build whose ATT MTU exceeds 515 octets (CONFIG_BT_L2CAP_TX_MTU and CONFIG_BT_BUF_ACL_RX_SIZE set for full-length attribute support); the shipped defaults are far smaller.
The overflow writes peer-controlled bytes past att_buf directly over the adjacent struct net_buf_simple net_buf — its data, __buf, len and size fields — which the subsequent long-read accumulation then uses as its destination, turning a small linear overflow into a controlled write. net_buf_simple_add() only asserts on insufficient tailroom unless CONFIG_NET_BUF_HARDENING is enabled, and that option is disabled by default, so ordinary production builds perform the copy. Beyond the in-tree LE Audio clients, any application subscriber that sized its receive buffer to the specification's 512-octet limit was exposed to the same overflow.
The fix rejects notification, indication and multiple-notification values longer than BT_ATT_MAX_ATTRIBUTE_LEN in call_notify_cb_and_maybe_unsubscribe() in subsys/bluetooth/host/gatt.c before any subscriber callback is invoked, so no subscriber can be handed more than the specified maximum. Remaining tuples of a multiple handle value notification are still delivered and oversized indications are still confirmed. |
| The AVRCP Target role in subsys/bluetooth/host/classic/avrcp.c keeps its vendor-dependent response transmit state in a per-connection object selected by connection index (get_avrcp_tg()), with the per-transfer context (tid, sent_len, and the BT_AVRCP_TG_FLAG_TX_ONGOING flag) stored in the user_data of the queued response net_buf. The AVCTP teardown handler avrcp_disconnected() did not cancel tg->vd_rsp_tx_work and did not release the buffers still queued on tg->vd_rsp_tx_pending, so a link drop in the middle of a fragmented response left the buffer on the list with TX_ONGOING still set.
A remote AVRCP Controller can trigger this deterministically: it issues a vendor-dependent command whose response exceeds one AVRCP fragment (for example GetElementAttributes or GetCapabilities), lets bt_avrcp_tg_vendor_tx_work() emit the START fragment, and then drops the ACL link instead of sending REQUEST_CONTINUING_RESPONSE. The AVCTP control channel requires an encrypted BR/EDR link (BT_SECURITY_L2), so the attacker must be a paired peer within radio range; no user interaction is needed.
Because the Target objects are static and reused, the next connection landing on the same connection index finds the stale buffer at the head of vd_rsp_tx_pending. Every run of the TX work sees TX_ONGOING and returns immediately, so all further vendor-dependent responses queue behind the stale head and are never sent — a persistent loss of AVRCP Target function that no timeout clears and only a reboot recovers. Each cycle also leaks one response buffer from a shallow application pool, and a new peer that sends REQUEST_CONTINUING_RESPONSE clears the stale TX_ONGOING via bt_avrcp_tg_process_continuing_cmd(), causing the un-sent remainder of the previous peer's response to be transmitted to it.
The fix cancels tg->vd_rsp_tx_work and unrefs every buffer on tg->vd_rsp_tx_pending in avrcp_disconnected(); since the TX context lives in the buffer user_data, releasing the buffers also resets the TX state machine. There is no memory corruption: the pre-fix buffer is leaked with a live reference, so no use-after-free arises. |
