| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: realtek: use gpiod_set_value_cansleep for reset GPIO
rtl83xx_reset_assert() and rtl83xx_reset_deassert() are only called from
the probe path, which may sleep and is not timing-critical. When the
reset GPIO is provided by a sleeping controller such as an I2C I/O
expander, gpiod_set_value() warns:
WARNING: drivers/gpio/gpiolib.c:4030 at gpiod_set_value+0x44/0x80, CPU#1: kworker/u16:4/61
Hardware name: B&O MAP CA33 Rev f (UNKNOWN) (DT)
Workqueue: events_unbound deferred_probe_work_func
pc : gpiod_set_value+0x44/0x80
lr : rtl83xx_probe+0x1d8/0x3a0
Call trace:
gpiod_set_value+0x44/0x80 (P)
rtl83xx_probe+0x1d8/0x3a0
realtek_mdio_probe+0x24/0xa0
mdio_probe+0x38/0x78
really_probe+0xc4/0x3e0
__driver_probe_device+0x15c/0x1b8
driver_probe_device+0xb4/0x120
__device_attach_driver+0xb8/0x1a0
bus_for_each_drv+0x88/0xf0
__device_attach+0xa0/0x1d8
device_initial_probe+0x54/0x68
bus_probe_device+0x38/0xa0
deferred_probe_work_func+0xb8/0x120
process_one_work+0x184/0x4e8
worker_thread+0x188/0x308
kthread+0x130/0x150
ret_from_fork+0x10/0x20
Switch both helpers to gpiod_set_value_cansleep() so such a reset GPIO can
be used without triggering the warning.
The reset GPIO has been driven with the non-sleeping gpiod_set_value()
since the driver was added in v4.19. The call has since been refactored
across several files - from realtek-smi.c / realtek-mdio.c into the common
rtl83xx.c module and then into the rtl83xx_reset_assert() and
rtl83xx_reset_deassert() helpers (both in v6.9). This patch therefore
applies as-is only to kernels that carry those helpers (v6.9+); older
stable kernels need the same gpiod_set_value_cansleep() conversion at the
corresponding open-coded call sites. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/shrinker: do not hold RCU lock in shrinker_debugfs_count_show()
Reading the debugfs "count" file of a memcg-aware shrinker can sleep
inside an RCU read-side critical section:
BUG: sleeping function called from invalid context at kernel/cgroup/rstat.c:421
RCU nest depth: 1, expected: 0
css_rstat_flush
mem_cgroup_flush_stats
zswap_shrinker_count
shrinker_debugfs_count_show
shrinker_debugfs_count_show() invokes the ->count_objects() callback under
rcu_read_lock(). The zswap callback flushes memcg stats via
css_rstat_flush(), which may sleep, so it must not run under RCU.
The RCU lock is not needed here. mem_cgroup_iter() takes RCU internally
and returns a memcg holding a css reference (dropped on the next iteration
or by mem_cgroup_iter_break()), so the memcg stays alive without it. The
shrinker is kept alive by the open debugfs file: shrinker_free() removes
the debugfs entries via debugfs_remove_recursive(), which waits for
in-flight readers to drain, before call_rcu(..., shrinker_free_rcu_cb).
The sibling "scan" handler already invokes the sleeping ->scan_objects()
callback with no RCU section.
Drop the rcu_read_lock()/rcu_read_unlock(). |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: sch: use raw_spinlock_t in the irq startup path
sch_irq_unmask() enables the GPIO IRQ and then updates the controller
state through sch_irq_mask_unmask(), which takes sch->lock with
spin_lock_irqsave(). The callback can be reached from irq_startup()
while setting up a requested IRQ. That path is not sleepable, but on
PREEMPT_RT a regular spinlock_t becomes a sleeping lock.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the request_threaded_irq() -> __setup_irq() ->
irq_startup() -> sch_irq_unmask() -> sch_irq_mask_unmask() carrier and
used the original spin_lock_irqsave(&sch->lock) edge. Lockdep reported:
BUG: sleeping function called from invalid context
hardirqs last disabled at ... __setup_irq.constprop.0 ... [vuln_msv]
sch_rt_spin_lock_irqsave+0x1c/0x30 [vuln_msv]
sch_irq_mask_unmask.constprop.0+0x31/0x70 [vuln_msv]
__setup_irq.constprop.0+0xd/0x30 [vuln_msv]
Convert the SCH controller lock to raw_spinlock_t. The same lock is
also used by the GPIO direction and value callbacks, but those critical
sections only update MMIO-backed GPIO registers and do not contain
sleepable operations. Keeping this register lock non-sleeping is
therefore appropriate for the irqchip callbacks and does not change the
GPIO-side locking contract. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: eic-sprd: use raw_spinlock_t in the irq startup path
sprd_eic_irq_unmask() enables the GPIO IRQ and then updates controller
state through sprd_eic_update(), which takes sprd_eic->lock with
spin_lock_irqsave(). The callback can be reached from irq_startup()
while setting up a requested IRQ. That path is not sleepable, but on
PREEMPT_RT a regular spinlock_t becomes a sleeping lock.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the request_threaded_irq() -> __setup_irq() ->
irq_startup() -> sprd_eic_irq_unmask() -> sprd_eic_update() carrier and
used the original spin_lock_irqsave(&sprd_eic->lock) edge. Lockdep
BUG: sleeping function called from invalid context
hardirqs last disabled at ... __setup_irq.constprop.0 ... [vuln_msv]
sprd_rt_spin_lock_irqsave+0x1c/0x30 [vuln_msv]
sprd_eic_update.constprop.0+0x48/0x90 [vuln_msv]
sprd_eic_irq_unmask.constprop.0+0x35/0x50 [vuln_msv]
__setup_irq.constprop.0+0xd/0x30 [vuln_msv]
Convert the Spreadtrum EIC controller lock to raw_spinlock_t. The
locked section only serializes MMIO register updates and does not contain
sleepable operations, so keeping it non-sleeping is appropriate for the
irqchip callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix warning in poll cq direct mode
CQs allocated by ib_alloc_cq() always have a comp_handler. Though
in direct mode this handler is never expected to be called, it
is still called when the driver is reset, triggering the following
WARN_ONCE():
Call trace:
ib_cq_completion_direct+0x38/0x60
hns_roce_cq_completion+0x54/0x90 (hns_roce_hw_v2]
hns_roce_handle_device_err+Ox1c8/0x340 [hns_roce_hw_v2]
hns_roce_hw_v2_uninit_instance.constprop.0+0x34/0x70 [hns_roce_hw_v2]
hns_roce_hw_v2_reset_notify+0xc4/0xe0 [hns_roce_hw_v2]
hclge_notify_roce_client+0x60/0xbc [hclge]
hclge_reset_rebuild+0x48/0x34c [hclge]
hclge_reset_subtask+0xcc/0xec [hclge]
hclge_reset_service_task+0x80/0x160 [hclge]
hclge_service_task+0x50/0x80 (hclge]
process_one_work+0x1cc/0x4d0
worker_thread+0x154/0x414
kthread+0x104/0x144
ret_from_fork+0x10/0x18 |
| In the Linux kernel, the following vulnerability has been resolved:
fsverity: Fix bpf_get_fsverity_digest() dynptr assumptions
The BPF verifier and the dynptr abstraction ensure that the memory space
referenced by a dynptr remains valid. They do not, however, provide any
guarantee that the contents of the memory are stable. kfuncs are
expected to remain memory-safe even if concurrent modifications occur.
bpf_get_fsverity_digest() didn't follow that: it could crash if
arg->digest_size was concurrently modified.
Fix that by using the known-good value hash_alg->digest_size instead.
Also widen 'dynptr_sz' and 'out_digest_sz' to u64 to match the return
type of __bpf_dynptr_size(). It doesn't appear that it can actually be
more than INT_MAX currently (since __bpf_dynptr_data_rw() excludes
file-based pointers), but the correct type might as well be used. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: dma-axi-dmac: use DMA pool to manange DMA descriptor
For architectures like Microblaze or arm64 (where this IP is used),
DMA_DIRECT_REMAP is set which means that dma_alloc_coherent() might
remap (and hence vmalloc()) some memory. This became visible in a design
where dma_direct_use_pool() is not possible.
With the above, when calling dma_free_coherent(), vunmap() would be
called from softirq context and thus leading to a BUG().
To fix it, use a dma pool that is allocated in
.device_alloc_chan_resources() and allocate blocks from it. The key
point is that now dma_pool_free() is used in axi_dmac_free_desc() to
free the blocks and that just frees the blocks from the pool in the
sense they can be used again. In other words, no actual call to
dma_free_coherent() happens. That only happens when destroying the pool
in axi_dmac_free_chan_resources() which does not happen in any interrupt
context. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: tracepoints: fix sleep while in atomic context in btrfs_sync_file()
The trace event btrfs_sync_file() is called in an atomic context (all trace
events are) and its call to dput(), which is needed due to the call to
dget_parent(), can sleep, triggering a kernel splat.
This can be reproduced by enabling the trace event and running btrfs/056
from fstests for example. The splat shown in dmesg is the following:
[53.919] BUG: sleeping function called from invalid context at fs/dcache.c:970
[53.947] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 32773, name: xfs_io
[53.988] preempt_count: 2, expected: 0
[53.967] RCU nest depth: 0, expected: 0
[53.943] Preemption disabled at:
[53.944] [<0000000000000000>] 0x0
[54.078] CPU: 0 UID: 0 PID: 32773 Comm: xfs_io Tainted: G W 7.1.0-rc1-btrfs-next-232+ #1 PREEMPT(full)
[54.070] Tainted: [W]=WARN
[54.071] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[54.072] Call Trace:
[54.074] <TASK>
[54.076] dump_stack_lvl+0x56/0x80
[54.079] __might_resched.cold+0xd6/0x10f
[54.072] dput.part.0+0x24/0x110
[54.078] trace_event_raw_event_btrfs_sync_file+0x75/0x140 [btrfs]
[54.089] btrfs_sync_file+0x1ed/0x530 [btrfs]
[54.087] ? __handle_mm_fault+0x8ae/0xed0
[54.089] btrfs_do_write_iter+0x172/0x210 [btrfs]
[54.091] vfs_write+0x21f/0x450
[54.094] __x64_sys_pwrite64+0x8d/0xc0
[54.096] ? do_user_addr_fault+0x20c/0x670
[54.099] do_syscall_64+0x60/0xf20
[54.092] ? clear_bhb_loop+0x60/0xb0
[54.094] entry_SYSCALL_64_after_hwframe+0x76/0x7e
So stop using dget_parent() and dput() and access the parent dentry
directly as dentry->d_parent. This is also what ext4 is doing in
its equivalent trace event ext4_sync_file_enter(). |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: use GFP_ATOMIC in wacom_wac_queue_flush()
wacom_wac_queue_flush() is called via the .raw_event callback
(wacom_raw_event → wacom_wac_pen_serial_enforce → wacom_wac_queue_flush).
For USB HID devices, this callback is invoked from hid_irq_in(), which
is a URB completion handler running in atomic context. Using GFP_KERNEL
in this path can sleep, leading to a "scheduling while atomic" bug.
Use GFP_ATOMIC instead. The existing code already handles allocation
failure by skipping the fifo entry and continuing. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas: don't kill URBs in interrupt context
Serialization for the TX path was enforced by calling
usb_kill_urb()/usb_kill_anchored_urbs(), to prevent transmission before
a previous URB was completed. usb_tx_block() can be called from
interrupt context (e.g. in the HCD giveback path), so we can't always
use it to kill in-flight URBs.
Prevent sleeping during interrupt context by checking the tx_submitted
anchor for existing URBs. We now return -EBUSY, to indicate there's
a pending request. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/efi: Fix graceful fault handling after FPU softirq changes
Since commit d02198550423 ("x86/fpu: Improve crypto performance by
making kernel-mode FPU reliably usable in softirqs"), kernel_fpu_begin()
calls fpregs_lock() which uses local_bh_disable() instead of the
previous preempt_disable(). This sets SOFTIRQ_OFFSET in preempt_count
during the entire EFI runtime service call, causing in_interrupt() to
return true in normal task context.
The graceful page fault handler efi_crash_gracefully_on_page_fault()
uses in_interrupt() to bail out for faults in real interrupt context.
With SOFTIRQ_OFFSET now set, the handler always bails out, leaving EFI
firmware page faults unhandled. This escalates to die() which also sees
in_interrupt() as true and calls panic("Fatal exception in interrupt"),
resulting in a hard system freeze. On systems with buggy firmware that
triggers page faults during EFI runtime calls (e.g., accessing unmapped
memory in GetTime()), this causes an unrecoverable hang instead of the
expected graceful EFI_ABORTED recovery.
Fix by replacing in_interrupt() with !in_task(). This preserves the
original intent of bailing for interrupts or NMI faults, while no longer
falsely triggering from the FPU code path's local_bh_disable().
[ardb: Sashiko spotted that using 'in_hardirq() || in_nmi()' leaves a
window where a softirq may be taken before fpregs_lock() is
called, but after efi_rts_work.efi_rts_id has been assigned,
and any page faults occurring in that window will then be
misidentified as having been caused by the firmware. Instead,
use !in_task(), which incorporates in_serving_softirq(). ] |
| A race condition in Grafana Live allows authenticated users with Viewer role to trigger a server crash by sending concurrent requests that cause a fatal map access error. This results in complete service unavailability requiring restart of the Grafana server. |
| emp3r0r is a C2 designed by Linux users for Linux environments. Prior to version 3.21.2, multiple shared maps are accessed without consistent synchronization across goroutines. Under concurrent activity, Go runtime can trigger `fatal error: concurrent map read and map write`, causing C2 process crash (availability loss). Version 3.21.2 fixes this issue. |
