| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix UMR hang in LAG error state unload
During firmware reset in LAG mode, a race condition causes the driver
to hang indefinitely while waiting for UMR completion during device
unload. See [1].
In LAG mode the bond device is only registered on the master, so it
never sees sys_error events from the slave.
During firmware reset this causes UMR waits to hang forever on unload
as the slave is dead but the master hasn't entered error state yet, so
UMR posts succeed but completions never arrive.
Fix this by adding a sys_error notifier that gets registered before
MLX5_IB_STAGE_IB_REG and stays alive until after ib_unregister_device().
This ensures error events reach the bond device throughout teardown.
[1]
Call Trace:
__schedule+0x2bd/0x760
schedule+0x37/0xa0
schedule_preempt_disabled+0xa/0x10
__mutex_lock.isra.6+0x2b5/0x4a0
__mlx5_ib_dereg_mr+0x606/0x870 [mlx5_ib]
? __xa_erase+0x4a/0xa0
? _cond_resched+0x15/0x30
? wait_for_completion+0x31/0x100
ib_dereg_mr_user+0x48/0xc0 [ib_core]
? rdmacg_uncharge_hierarchy+0xa0/0x100
destroy_hw_idr_uobject+0x20/0x50 [ib_uverbs]
uverbs_destroy_uobject+0x37/0x150 [ib_uverbs]
__uverbs_cleanup_ufile+0xda/0x140 [ib_uverbs]
uverbs_destroy_ufile_hw+0x3a/0xf0 [ib_uverbs]
ib_uverbs_remove_one+0xc3/0x140 [ib_uverbs]
remove_client_context+0x8b/0xd0 [ib_core]
disable_device+0x8c/0x130 [ib_core]
__ib_unregister_device+0x10d/0x180 [ib_core]
ib_unregister_device+0x21/0x30 [ib_core]
__mlx5_ib_remove+0x1e4/0x1f0 [mlx5_ib]
auxiliary_bus_remove+0x1e/0x30
device_release_driver_internal+0x103/0x1f0
bus_remove_device+0xf7/0x170
device_del+0x181/0x410
mlx5_rescan_drivers_locked.part.10+0xa9/0x1d0 [mlx5_core]
mlx5_disable_lag+0x253/0x260 [mlx5_core]
mlx5_lag_disable_change+0x89/0xc0 [mlx5_core]
mlx5_eswitch_disable+0x67/0xa0 [mlx5_core]
mlx5_unload+0x15/0xd0 [mlx5_core]
mlx5_unload_one+0x71/0xc0 [mlx5_core]
mlx5_sync_reset_reload_work+0x83/0x100 [mlx5_core]
process_one_work+0x1a7/0x360
worker_thread+0x30/0x390
? create_worker+0x1a0/0x1a0
kthread+0x116/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x22/0x40 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/eeh: fix recursive pci_lock_rescan_remove locking in EEH event handling
The recent commit 1010b4c012b0 ("powerpc/eeh: Make EEH driver device
hotplug safe") restructured the EEH driver to improve synchronization
with the PCI hotplug layer.
However, it inadvertently moved pci_lock_rescan_remove() outside its
intended scope in eeh_handle_normal_event(), leading to broken PCI
error reporting and improper EEH event triggering. Specifically,
eeh_handle_normal_event() acquired pci_lock_rescan_remove() before
calling eeh_pe_bus_get(), but eeh_pe_bus_get() itself attempts to
acquire the same lock internally, causing nested locking and disrupting
normal EEH event handling paths.
This patch adds a boolean parameter do_lock to _eeh_pe_bus_get(),
with two public wrappers:
eeh_pe_bus_get() with locking enabled.
eeh_pe_bus_get_nolock() that skips locking.
Callers that already hold pci_lock_rescan_remove() now use
eeh_pe_bus_get_nolock() to avoid recursive lock acquisition.
Additionally, pci_lock_rescan_remove() calls are restored to the correct
position—after eeh_pe_bus_get() and immediately before iterating affected
PEs and devices. This ensures EEH-triggered PCI removes occur under proper
bus rescan locking without recursive lock contention.
The eeh_pe_loc_get() function has been split into two functions:
eeh_pe_loc_get(struct eeh_pe *pe) which retrieves the loc for given PE.
eeh_pe_loc_get_bus(struct pci_bus *bus) which retrieves the location
code for given bus.
This resolves lockdep warnings such as:
<snip>
[ 84.964298] [ T928] ============================================
[ 84.964304] [ T928] WARNING: possible recursive locking detected
[ 84.964311] [ T928] 6.18.0-rc3 #51 Not tainted
[ 84.964315] [ T928] --------------------------------------------
[ 84.964320] [ T928] eehd/928 is trying to acquire lock:
[ 84.964324] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964342] [ T928]
but task is already holding lock:
[ 84.964347] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964357] [ T928]
other info that might help us debug this:
[ 84.964363] [ T928] Possible unsafe locking scenario:
[ 84.964367] [ T928] CPU0
[ 84.964370] [ T928] ----
[ 84.964373] [ T928] lock(pci_rescan_remove_lock);
[ 84.964378] [ T928] lock(pci_rescan_remove_lock);
[ 84.964383] [ T928]
*** DEADLOCK ***
[ 84.964388] [ T928] May be due to missing lock nesting notation
[ 84.964393] [ T928] 1 lock held by eehd/928:
[ 84.964397] [ T928] #0: c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964408] [ T928]
stack backtrace:
[ 84.964414] [ T928] CPU: 2 UID: 0 PID: 928 Comm: eehd Not tainted 6.18.0-rc3 #51 VOLUNTARY
[ 84.964417] [ T928] Hardware name: IBM,9080-HEX POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_022) hv:phyp pSeries
[ 84.964419] [ T928] Call Trace:
[ 84.964420] [ T928] [c0000011a7157990] [c000000001705de4] dump_stack_lvl+0xc8/0x130 (unreliable)
[ 84.964424] [ T928] [c0000011a71579d0] [c0000000002f66e0] print_deadlock_bug+0x430/0x440
[ 84.964428] [ T928] [c0000011a7157a70] [c0000000002fd0c0] __lock_acquire+0x1530/0x2d80
[ 84.964431] [ T928] [c0000011a7157ba0] [c0000000002fea54] lock_acquire+0x144/0x410
[ 84.964433] [ T928] [c0000011a7157cb0] [c0000011a7157cb0] __mutex_lock+0xf4/0x1050
[ 84.964436] [ T928] [c0000011a7157e00] [c000000000de21d8] pci_lock_rescan_remove+0x28/0x40
[ 84.964439] [ T928] [c0000011a7157e20] [c00000000004ed98] eeh_pe_bus_get+0x48/0xc0
[ 84.964442] [ T928] [c0000011a7157e50] [c00000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: revert commit_mutex usage in reset path
It causes circular lock dependency between commit_mutex, nfnl_subsys_ipset
and nlk_cb_mutex when nft reset, ipset list, and iptables-nft with '-m set'
rule run at the same time.
Previous patches made it safe to run individual reset handlers concurrently
so commit_mutex is no longer required to prevent this. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix deadlock between devlink lock and esw->wq
esw->work_queue executes esw_functions_changed_event_handler ->
esw_vfs_changed_event_handler and acquires the devlink lock.
.eswitch_mode_set (acquires devlink lock in devlink_nl_pre_doit) ->
mlx5_devlink_eswitch_mode_set -> mlx5_eswitch_disable_locked ->
mlx5_eswitch_event_handler_unregister -> flush_workqueue deadlocks
when esw_vfs_changed_event_handler executes.
Fix that by no longer flushing the work to avoid the deadlock, and using
a generation counter to keep track of work relevance. This avoids an old
handler manipulating an esw that has undergone one or more mode changes:
- the counter is incremented in mlx5_eswitch_event_handler_unregister.
- the counter is read and passed to the ephemeral mlx5_host_work struct.
- the work handler takes the devlink lock and bails out if the current
generation is different than the one it was scheduled to operate on.
- mlx5_eswitch_cleanup does the final draining before destroying the wq.
No longer flushing the workqueue has the side effect of maybe no longer
cancelling pending vport_change_handler work items, but that's ok since
those are disabled elsewhere:
- mlx5_eswitch_disable_locked disables the vport eq notifier.
- mlx5_esw_vport_disable disarms the HW EQ notification and marks
vport->enabled under state_lock to false to prevent pending vport
handler from doing anything.
- mlx5_eswitch_cleanup destroys the workqueue and makes sure all events
are disabled/finished. |
| In the Linux kernel, the following vulnerability has been resolved:
md raid: fix hang when stopping arrays with metadata through dm-raid
When using device-mapper's dm-raid target, stopping a RAID array can cause
the system to hang under specific conditions.
This occurs when:
- A dm-raid managed device tree is suspended from top to bottom
(the top-level RAID device is suspended first, followed by its
underlying metadata and data devices)
- The top-level RAID device is then removed
Removing the top-level device triggers a hang in the following sequence:
the dm-raid destructor calls md_stop(), which tries to flush the
write-intent bitmap by writing to the metadata sub-devices. However, these
devices are already suspended, making them unable to complete the write-intent
operations and causing an indefinite block.
Fix:
- Prevent bitmap flushing when md_stop() is called from dm-raid
destructor context
and avoid a quiescing/unquescing cycle which could also cause I/O
- Still allow write-intent bitmap flushing when called from dm-raid
suspend context
This ensures that RAID array teardown can complete successfully even when the
underlying devices are in a suspended state.
This second patch uses md_is_rdwr() to distinguish between suspend and
destructor paths as elaborated on above. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV"
This reverts commit 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking
when enabling/disabling SR-IOV"), which causes a deadlock by recursively
taking pci_rescan_remove_lock when sriov_del_vfs() is called as part of
pci_stop_and_remove_bus_device(). For example with the following sequence
of commands:
$ echo <NUM> > /sys/bus/pci/devices/<pf>/sriov_numvfs
$ echo 1 > /sys/bus/pci/devices/<pf>/remove
A trimmed trace of the deadlock on a mlx5 device is as below:
zsh/5715 is trying to acquire lock:
000002597926ef50 (pci_rescan_remove_lock){+.+.}-{3:3}, at: sriov_disable+0x34/0x140
but task is already holding lock:
000002597926ef50 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_stop_and_remove_bus_device_locked+0x24/0x80
...
Call Trace:
[<00000259778c4f90>] dump_stack_lvl+0xc0/0x110
[<00000259779c844e>] print_deadlock_bug+0x31e/0x330
[<00000259779c1908>] __lock_acquire+0x16c8/0x32f0
[<00000259779bffac>] lock_acquire+0x14c/0x350
[<00000259789643a6>] __mutex_lock_common+0xe6/0x1520
[<000002597896413c>] mutex_lock_nested+0x3c/0x50
[<00000259784a07e4>] sriov_disable+0x34/0x140
[<00000258f7d6dd80>] mlx5_sriov_disable+0x50/0x80 [mlx5_core]
[<00000258f7d5745e>] remove_one+0x5e/0xf0 [mlx5_core]
[<00000259784857fc>] pci_device_remove+0x3c/0xa0
[<000002597851012e>] device_release_driver_internal+0x18e/0x280
[<000002597847ae22>] pci_stop_bus_device+0x82/0xa0
[<000002597847afce>] pci_stop_and_remove_bus_device_locked+0x5e/0x80
[<00000259784972c2>] remove_store+0x72/0x90
[<0000025977e6661a>] kernfs_fop_write_iter+0x15a/0x200
[<0000025977d7241c>] vfs_write+0x24c/0x300
[<0000025977d72696>] ksys_write+0x86/0x110
[<000002597895b61c>] __do_syscall+0x14c/0x400
[<000002597896e0ee>] system_call+0x6e/0x90
This alone is not a complete fix as it restores the issue the cited commit
tried to solve. A new fix will be provided as a follow on. |
| In the Linux kernel, the following vulnerability has been resolved:
igb: remove napi_synchronize() in igb_down()
When an AF_XDP zero-copy application terminates abruptly (e.g., kill -9),
the XSK buffer pool is destroyed but NAPI polling continues.
igb_clean_rx_irq_zc() repeatedly returns the full budget, preventing
napi_complete_done() from clearing NAPI_STATE_SCHED.
igb_down() calls napi_synchronize() before napi_disable() for each queue
vector. napi_synchronize() spins waiting for NAPI_STATE_SCHED to clear,
which never happens. igb_down() blocks indefinitely, the TX watchdog
fires, and the TX queue remains permanently stalled.
napi_disable() already handles this correctly: it sets NAPI_STATE_DISABLE.
After a full-budget poll, __napi_poll() checks napi_disable_pending(). If
set, it forces completion and clears NAPI_STATE_SCHED, breaking the loop
that napi_synchronize() cannot.
napi_synchronize() was added in commit 41f149a285da ("igb: Fix possible
panic caused by Rx traffic arrival while interface is down").
napi_disable() provides stronger guarantees: it prevents further
scheduling and waits for any active poll to exit.
Other Intel drivers (ixgbe, ice, i40e) use napi_disable() without a
preceding napi_synchronize() in their down paths.
Remove redundant napi_synchronize() call and reorder napi_disable()
before igb_set_queue_napi() so the queue-to-NAPI mapping is only
cleared after polling has fully stopped. |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: fix PREEMPT_RT raw/bh spinlock nesting for async VC handling
Switch from using the completion's raw spinlock to a local lock in the
idpf_vc_xn struct. The conversion is safe because complete/_all() are
called outside the lock and there is no reason to share the completion
lock in the current logic. This avoids invalid wait context reported by
the kernel due to the async handler taking BH spinlock:
[ 805.726977] =============================
[ 805.726991] [ BUG: Invalid wait context ]
[ 805.727006] 7.0.0-rc2-net-devq-031026+ #28 Tainted: G S OE
[ 805.727026] -----------------------------
[ 805.727038] kworker/u261:0/572 is trying to lock:
[ 805.727051] ff190da6a8dbb6a0 (&vport_config->mac_filter_list_lock){+...}-{3:3}, at: idpf_mac_filter_async_handler+0xe9/0x260 [idpf]
[ 805.727099] other info that might help us debug this:
[ 805.727111] context-{5:5}
[ 805.727119] 3 locks held by kworker/u261:0/572:
[ 805.727132] #0: ff190da6db3e6148 ((wq_completion)idpf-0000:83:00.0-mbx){+.+.}-{0:0}, at: process_one_work+0x4b5/0x730
[ 805.727163] #1: ff3c6f0a6131fe50 ((work_completion)(&(&adapter->mbx_task)->work)){+.+.}-{0:0}, at: process_one_work+0x1e5/0x730
[ 805.727191] #2: ff190da765190020 (&x->wait#34){+.+.}-{2:2}, at: idpf_recv_mb_msg+0xc8/0x710 [idpf]
[ 805.727218] stack backtrace:
...
[ 805.727238] Workqueue: idpf-0000:83:00.0-mbx idpf_mbx_task [idpf]
[ 805.727247] Call Trace:
[ 805.727249] <TASK>
[ 805.727251] dump_stack_lvl+0x77/0xb0
[ 805.727259] __lock_acquire+0xb3b/0x2290
[ 805.727268] ? __irq_work_queue_local+0x59/0x130
[ 805.727275] lock_acquire+0xc6/0x2f0
[ 805.727277] ? idpf_mac_filter_async_handler+0xe9/0x260 [idpf]
[ 805.727284] ? _printk+0x5b/0x80
[ 805.727290] _raw_spin_lock_bh+0x38/0x50
[ 805.727298] ? idpf_mac_filter_async_handler+0xe9/0x260 [idpf]
[ 805.727303] idpf_mac_filter_async_handler+0xe9/0x260 [idpf]
[ 805.727310] idpf_recv_mb_msg+0x1c8/0x710 [idpf]
[ 805.727317] process_one_work+0x226/0x730
[ 805.727322] worker_thread+0x19e/0x340
[ 805.727325] ? __pfx_worker_thread+0x10/0x10
[ 805.727328] kthread+0xf4/0x130
[ 805.727333] ? __pfx_kthread+0x10/0x10
[ 805.727336] ret_from_fork+0x32c/0x410
[ 805.727345] ? __pfx_kthread+0x10/0x10
[ 805.727347] ret_from_fork_asm+0x1a/0x30
[ 805.727354] </TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
wireguard: device: use exit_rtnl callback instead of manual rtnl_lock in pre_exit
wg_netns_pre_exit() manually acquires rtnl_lock() inside the
pernet .pre_exit callback. This causes a hung task when another
thread holds rtnl_mutex - the cleanup_net workqueue (or the
setup_net failure rollback path) blocks indefinitely in
wg_netns_pre_exit() waiting to acquire the lock.
Convert to .exit_rtnl, introduced in commit 7a60d91c690b ("net:
Add ->exit_rtnl() hook to struct pernet_operations."), where the
framework already holds RTNL and batches all callbacks under a
single rtnl_lock()/rtnl_unlock() pair, eliminating the contention
window.
The rcu_assign_pointer(wg->creating_net, NULL) is safe to move
from .pre_exit to .exit_rtnl (which runs after synchronize_rcu())
because all RCU readers of creating_net either use maybe_get_net()
- which returns NULL for a dying namespace with zero refcount - or
access net->user_ns which remains valid throughout the entire
ops_undo_list sequence.
[ Jason: added __net_exit and __read_mostly annotations that were missing. ] |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix deadlock in l2cap_conn_del()
l2cap_conn_del() calls cancel_delayed_work_sync() for both info_timer
and id_addr_timer while holding conn->lock. However, the work functions
l2cap_info_timeout() and l2cap_conn_update_id_addr() both acquire
conn->lock, creating a potential AB-BA deadlock if the work is already
executing when l2cap_conn_del() takes the lock.
Move the work cancellations before acquiring conn->lock and use
disable_delayed_work_sync() to additionally prevent the works from
being rearmed after cancellation, consistent with the pattern used in
hci_conn_del(). |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix potential deadlock in cpu hotplug with osnoise
The following sequence may leads deadlock in cpu hotplug:
task1 task2 task3
----- ----- -----
mutex_lock(&interface_lock)
[CPU GOING OFFLINE]
cpus_write_lock();
osnoise_cpu_die();
kthread_stop(task3);
wait_for_completion();
osnoise_sleep();
mutex_lock(&interface_lock);
cpus_read_lock();
[DEAD LOCK]
Fix by swap the order of cpus_read_lock() and mutex_lock(&interface_lock). |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: register phy led_triggers during probe to avoid AB-BA deadlock
There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and
LED_TRIGGER_PHY are enabled:
[ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock);
[ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234
[ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c
[ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c
[ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0
[ 1362.075849] [<806d714c>] __dev_open+0x280/0x2b0
[ 1362.080384] [<806d7668>] __dev_change_flags+0x244/0x24c
[ 1362.085598] [<806d7698>] dev_change_flags+0x28/0x78
[ 1362.090528] [<807150e4>] dev_ioctl+0x4c0/0x654 <-- Hold lock "rtnl_mutex" by calling rtnl_lock();
[ 1362.094985] [<80694360>] sock_ioctl+0x2f4/0x4e0
[ 1362.099567] [<802e9c4c>] sys_ioctl+0x32c/0xd8c
[ 1362.104022] [<80014504>] syscall_common+0x34/0x58
Here LED_TRIGGER_PHY is registering LED triggers during phy_attach
while holding RTNL and then taking triggers_list_lock.
[ 1362.191101] [<806c2640>] register_netdevice_notifier+0x60/0x168 <-- Trying to get lock "rtnl_mutex" via rtnl_lock();
[ 1362.197073] [<805504ac>] netdev_trig_activate+0x194/0x1e4
[ 1362.202490] [<8054e28c>] led_trigger_set+0x1d4/0x360 <-- Hold lock "triggers_list_lock" by down_read(&triggers_list_lock);
[ 1362.207511] [<8054eb38>] led_trigger_write+0xd8/0x14c
[ 1362.212566] [<80381d98>] sysfs_kf_bin_write+0x80/0xbc
[ 1362.217688] [<8037fcd8>] kernfs_fop_write_iter+0x17c/0x28c
[ 1362.223174] [<802cbd70>] vfs_write+0x21c/0x3c4
[ 1362.227712] [<802cc0c4>] ksys_write+0x78/0x12c
[ 1362.232164] [<80014504>] syscall_common+0x34/0x58
Here LEDS_TRIGGER_NETDEV is being enabled on an LED. It first takes
triggers_list_lock and then RTNL. A classical AB-BA deadlock.
phy_led_triggers_registers() does not require the RTNL, it does not
make any calls into the network stack which require protection. There
is also no requirement the PHY has been attached to a MAC, the
triggers only make use of phydev state. This allows the call to
phy_led_triggers_registers() to be placed elsewhere. PHY probe() and
release() don't hold RTNL, so solving the AB-BA deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
can: mcp251x: fix deadlock in error path of mcp251x_open
The mcp251x_open() function call free_irq() in its error path with the
mpc_lock mutex held. But if an interrupt already occurred the
interrupt handler will be waiting for the mpc_lock and free_irq() will
deadlock waiting for the handler to finish.
This issue is similar to the one fixed in commit 7dd9c26bd6cf ("can:
mcp251x: fix deadlock if an interrupt occurs during mcp251x_open") but
for the error path.
To solve this issue move the call to free_irq() after the lock is
released. Setting `priv->force_quit = 1` beforehand ensure that the IRQ
handler will exit right away once it acquired the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: Don't register LEDs for genphy
If a PHY has no driver, the genphy driver is probed/removed directly in
phy_attach/detach. If the PHY's ofnode has an "leds" subnode, then the
LEDs will be (un)registered when probing/removing the genphy driver.
This could occur if the leds are for a non-generic driver that isn't
loaded for whatever reason. Synchronously removing the PHY device in
phy_detach leads to the following deadlock:
rtnl_lock()
ndo_close()
...
phy_detach()
phy_remove()
phy_leds_unregister()
led_classdev_unregister()
led_trigger_set()
netdev_trigger_deactivate()
unregister_netdevice_notifier()
rtnl_lock()
There is a corresponding deadlock on the open/register side of things
(and that one is reported by lockdep), but it requires a race while this
one is deterministic.
Generic PHYs do not support LEDs anyway, so don't bother registering
them. |
| In the Linux kernel, the following vulnerability has been resolved:
PM: hibernate: Avoid deadlock in hibernate_compressor_param_set()
syzbot reported a deadlock in lock_system_sleep() (see below).
The write operation to "/sys/module/hibernate/parameters/compressor"
conflicts with the registration of ieee80211 device, resulting in a deadlock
when attempting to acquire system_transition_mutex under param_lock.
To avoid this deadlock, change hibernate_compressor_param_set() to use
mutex_trylock() for attempting to acquire system_transition_mutex and
return -EBUSY when it fails.
Task flags need not be saved or adjusted before calling
mutex_trylock(&system_transition_mutex) because the caller is not going
to end up waiting for this mutex and if it runs concurrently with system
suspend in progress, it will be frozen properly when it returns to user
space.
syzbot report:
syz-executor895/5833 is trying to acquire lock:
ffffffff8e0828c8 (system_transition_mutex){+.+.}-{4:4}, at: lock_system_sleep+0x87/0xa0 kernel/power/main.c:56
but task is already holding lock:
ffffffff8e07dc68 (param_lock){+.+.}-{4:4}, at: kernel_param_lock kernel/params.c:607 [inline]
ffffffff8e07dc68 (param_lock){+.+.}-{4:4}, at: param_attr_store+0xe6/0x300 kernel/params.c:586
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (param_lock){+.+.}-{4:4}:
__mutex_lock_common kernel/locking/mutex.c:585 [inline]
__mutex_lock+0x19b/0xb10 kernel/locking/mutex.c:730
ieee80211_rate_control_ops_get net/mac80211/rate.c:220 [inline]
rate_control_alloc net/mac80211/rate.c:266 [inline]
ieee80211_init_rate_ctrl_alg+0x18d/0x6b0 net/mac80211/rate.c:1015
ieee80211_register_hw+0x20cd/0x4060 net/mac80211/main.c:1531
mac80211_hwsim_new_radio+0x304e/0x54e0 drivers/net/wireless/virtual/mac80211_hwsim.c:5558
init_mac80211_hwsim+0x432/0x8c0 drivers/net/wireless/virtual/mac80211_hwsim.c:6910
do_one_initcall+0x128/0x700 init/main.c:1257
do_initcall_level init/main.c:1319 [inline]
do_initcalls init/main.c:1335 [inline]
do_basic_setup init/main.c:1354 [inline]
kernel_init_freeable+0x5c7/0x900 init/main.c:1568
kernel_init+0x1c/0x2b0 init/main.c:1457
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:148
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
-> #2 (rtnl_mutex){+.+.}-{4:4}:
__mutex_lock_common kernel/locking/mutex.c:585 [inline]
__mutex_lock+0x19b/0xb10 kernel/locking/mutex.c:730
wg_pm_notification drivers/net/wireguard/device.c:80 [inline]
wg_pm_notification+0x49/0x180 drivers/net/wireguard/device.c:64
notifier_call_chain+0xb7/0x410 kernel/notifier.c:85
notifier_call_chain_robust kernel/notifier.c:120 [inline]
blocking_notifier_call_chain_robust kernel/notifier.c:345 [inline]
blocking_notifier_call_chain_robust+0xc9/0x170 kernel/notifier.c:333
pm_notifier_call_chain_robust+0x27/0x60 kernel/power/main.c:102
snapshot_open+0x189/0x2b0 kernel/power/user.c:77
misc_open+0x35a/0x420 drivers/char/misc.c:179
chrdev_open+0x237/0x6a0 fs/char_dev.c:414
do_dentry_open+0x735/0x1c40 fs/open.c:956
vfs_open+0x82/0x3f0 fs/open.c:1086
do_open fs/namei.c:3830 [inline]
path_openat+0x1e88/0x2d80 fs/namei.c:3989
do_filp_open+0x20c/0x470 fs/namei.c:4016
do_sys_openat2+0x17a/0x1e0 fs/open.c:1428
do_sys_open fs/open.c:1443 [inline]
__do_sys_openat fs/open.c:1459 [inline]
__se_sys_openat fs/open.c:1454 [inline]
__x64_sys_openat+0x175/0x210 fs/open.c:1454
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #1 ((pm_chain_head).rwsem){++++}-{4:4}:
down_read+0x9a/0x330 kernel/locking/rwsem.c:1524
blocking_notifier_call_chain_robust kerne
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: vlan: don't propagate flags on open
With the device instance lock, there is now a possibility of a deadlock:
[ 1.211455] ============================================
[ 1.211571] WARNING: possible recursive locking detected
[ 1.211687] 6.14.0-rc5-01215-g032756b4ca7a-dirty #5 Not tainted
[ 1.211823] --------------------------------------------
[ 1.211936] ip/184 is trying to acquire lock:
[ 1.212032] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_set_allmulti+0x4e/0xb0
[ 1.212207]
[ 1.212207] but task is already holding lock:
[ 1.212332] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0
[ 1.212487]
[ 1.212487] other info that might help us debug this:
[ 1.212626] Possible unsafe locking scenario:
[ 1.212626]
[ 1.212751] CPU0
[ 1.212815] ----
[ 1.212871] lock(&dev->lock);
[ 1.212944] lock(&dev->lock);
[ 1.213016]
[ 1.213016] *** DEADLOCK ***
[ 1.213016]
[ 1.213143] May be due to missing lock nesting notation
[ 1.213143]
[ 1.213294] 3 locks held by ip/184:
[ 1.213371] #0: ffffffff838b53e0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x1b/0xa0
[ 1.213543] #1: ffffffff84e5fc70 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x37/0xa0
[ 1.213727] #2: ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0
[ 1.213895]
[ 1.213895] stack backtrace:
[ 1.213991] CPU: 0 UID: 0 PID: 184 Comm: ip Not tainted 6.14.0-rc5-01215-g032756b4ca7a-dirty #5
[ 1.213993] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 1.213994] Call Trace:
[ 1.213995] <TASK>
[ 1.213996] dump_stack_lvl+0x8e/0xd0
[ 1.214000] print_deadlock_bug+0x28b/0x2a0
[ 1.214020] lock_acquire+0xea/0x2a0
[ 1.214027] __mutex_lock+0xbf/0xd40
[ 1.214038] dev_set_allmulti+0x4e/0xb0 # real_dev->flags & IFF_ALLMULTI
[ 1.214040] vlan_dev_open+0xa5/0x170 # ndo_open on vlandev
[ 1.214042] __dev_open+0x145/0x270
[ 1.214046] __dev_change_flags+0xb0/0x1e0
[ 1.214051] netif_change_flags+0x22/0x60 # IFF_UP vlandev
[ 1.214053] dev_change_flags+0x61/0xb0 # for each device in group from dev->vlan_info
[ 1.214055] vlan_device_event+0x766/0x7c0 # on netdevsim0
[ 1.214058] notifier_call_chain+0x78/0x120
[ 1.214062] netif_open+0x6d/0x90
[ 1.214064] dev_open+0x5b/0xb0 # locks netdevsim0
[ 1.214066] bond_enslave+0x64c/0x1230
[ 1.214075] do_set_master+0x175/0x1e0 # on netdevsim0
[ 1.214077] do_setlink+0x516/0x13b0
[ 1.214094] rtnl_newlink+0xaba/0xb80
[ 1.214132] rtnetlink_rcv_msg+0x440/0x490
[ 1.214144] netlink_rcv_skb+0xeb/0x120
[ 1.214150] netlink_unicast+0x1f9/0x320
[ 1.214153] netlink_sendmsg+0x346/0x3f0
[ 1.214157] __sock_sendmsg+0x86/0xb0
[ 1.214160] ____sys_sendmsg+0x1c8/0x220
[ 1.214164] ___sys_sendmsg+0x28f/0x2d0
[ 1.214179] __x64_sys_sendmsg+0xef/0x140
[ 1.214184] do_syscall_64+0xec/0x1d0
[ 1.214190] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 1.214191] RIP: 0033:0x7f2d1b4a7e56
Device setup:
netdevsim0 (down)
^ ^
bond netdevsim1.100@netdevsim1 allmulticast=on (down)
When we enslave the lower device (netdevsim0) which has a vlan, we
propagate vlan's allmuti/promisc flags during ndo_open. This causes
(re)locking on of the real_dev.
Propagate allmulti/promisc on flags change, not on the open. There
is a slight semantics change that vlans that are down now propagate
the flags, but this seems unlikely to result in the real issues.
Reproducer:
echo 0 1 > /sys/bus/netdevsim/new_device
dev_path=$(ls -d /sys/bus/netdevsim/devices/netdevsim0/net/*)
dev=$(echo $dev_path | rev | cut -d/ -f1 | rev)
ip link set dev $dev name netdevsim0
ip link set dev netdevsim0 up
ip link add link netdevsim0 name netdevsim0.100 type vlan id 100
ip link set dev netdevsim0.100 allm
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: switchdev: Convert blocking notification chain to a raw one
A blocking notification chain uses a read-write semaphore to protect the
integrity of the chain. The semaphore is acquired for writing when
adding / removing notifiers to / from the chain and acquired for reading
when traversing the chain and informing notifiers about an event.
In case of the blocking switchdev notification chain, recursive
notifications are possible which leads to the semaphore being acquired
twice for reading and to lockdep warnings being generated [1].
Specifically, this can happen when the bridge driver processes a
SWITCHDEV_BRPORT_UNOFFLOADED event which causes it to emit notifications
about deferred events when calling switchdev_deferred_process().
Fix this by converting the notification chain to a raw notification
chain in a similar fashion to the netdev notification chain. Protect
the chain using the RTNL mutex by acquiring it when modifying the chain.
Events are always informed under the RTNL mutex, but add an assertion in
call_switchdev_blocking_notifiers() to make sure this is not violated in
the future.
Maintain the "blocking" prefix as events are always emitted from process
context and listeners are allowed to block.
[1]:
WARNING: possible recursive locking detected
6.14.0-rc4-custom-g079270089484 #1 Not tainted
--------------------------------------------
ip/52731 is trying to acquire lock:
ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
but task is already holding lock:
ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((switchdev_blocking_notif_chain).rwsem);
lock((switchdev_blocking_notif_chain).rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by ip/52731:
#0: ffffffff84f795b0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_newlink+0x727/0x1dc0
#1: ffffffff8731f628 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_newlink+0x790/0x1dc0
#2: ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
stack backtrace:
...
? __pfx_down_read+0x10/0x10
? __pfx_mark_lock+0x10/0x10
? __pfx_switchdev_port_attr_set_deferred+0x10/0x10
blocking_notifier_call_chain+0x58/0xa0
switchdev_port_attr_notify.constprop.0+0xb3/0x1b0
? __pfx_switchdev_port_attr_notify.constprop.0+0x10/0x10
? mark_held_locks+0x94/0xe0
? switchdev_deferred_process+0x11a/0x340
switchdev_port_attr_set_deferred+0x27/0xd0
switchdev_deferred_process+0x164/0x340
br_switchdev_port_unoffload+0xc8/0x100 [bridge]
br_switchdev_blocking_event+0x29f/0x580 [bridge]
notifier_call_chain+0xa2/0x440
blocking_notifier_call_chain+0x6e/0xa0
switchdev_bridge_port_unoffload+0xde/0x1a0
... |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: avoid holding freeze_mutex during mmap operation
We use map->freeze_mutex to prevent races between map_freeze() and
memory mapping BPF map contents with writable permissions. The way we
naively do this means we'll hold freeze_mutex for entire duration of all
the mm and VMA manipulations, which is completely unnecessary. This can
potentially also lead to deadlocks, as reported by syzbot in [0].
So, instead, hold freeze_mutex only during writeability checks, bump
(proactively) "write active" count for the map, unlock the mutex and
proceed with mmap logic. And only if something went wrong during mmap
logic, then undo that "write active" counter increment.
[0] https://lore.kernel.org/bpf/678dcbc9.050a0220.303755.0066.GAE@google.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
block: mark GFP_NOIO around sysfs ->store()
sysfs ->store is called with queue freezed, meantime we have several
->store() callbacks(update_nr_requests, wbt, scheduler) to allocate
memory with GFP_KERNEL which may run into direct reclaim code path,
then potential deadlock can be caused.
Fix the issue by marking NOIO around sysfs ->store() |
| A denial of service vulnerability was found in tipc_crypto_key_revoke in net/tipc/crypto.c in the Linux kernel’s TIPC subsystem. This flaw allows guests with local user privileges to trigger a deadlock and potentially crash the system. |
