| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Kill timer properly at removal
The USB-audio MIDI code initializes the timer, but in a rare case, the
driver might be freed without the disconnect call. This leaves the
timer in an active state while the assigned object is released via
snd_usbmidi_free(), which ends up with a kernel warning when the debug
configuration is enabled, as spotted by fuzzer.
For avoiding the problem, put timer_shutdown_sync() at
snd_usbmidi_free(), so that the timer can be killed properly.
While we're at it, replace the existing timer_delete_sync() at the
disconnect callback with timer_shutdown_sync(), too. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Disable SCO support if READ_VOICE_SETTING is unsupported/broken
A SCO connection without the proper voice_setting can cause
the controller to lock up. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: don't warn when if there is a FW error
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Check return value from memblock_phys_alloc_range()
At least with CONFIG_PHYSICAL_START=0x100000, if there is < 4 MiB of
contiguous free memory available at this point, the kernel will crash
and burn because memblock_phys_alloc_range() returns 0 on failure,
which leads memblock_phys_free() to throw the first 4 MiB of physical
memory to the wolves.
At a minimum it should fail gracefully with a meaningful diagnostic,
but in fact everything seems to work fine without the weird reserve
allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
rseq: Fix segfault on registration when rseq_cs is non-zero
The rseq_cs field is documented as being set to 0 by user-space prior to
registration, however this is not currently enforced by the kernel. This
can result in a segfault on return to user-space if the value stored in
the rseq_cs field doesn't point to a valid struct rseq_cs.
The correct solution to this would be to fail the rseq registration when
the rseq_cs field is non-zero. However, some older versions of glibc
will reuse the rseq area of previous threads without clearing the
rseq_cs field and will also terminate the process if the rseq
registration fails in a secondary thread. This wasn't caught in testing
because in this case the leftover rseq_cs does point to a valid struct
rseq_cs.
What we can do is clear the rseq_cs field on registration when it's
non-zero which will prevent segfaults on registration and won't break
the glibc versions that reuse rseq areas on thread creation. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix unconditional IO throttle caused by REQ_PREFLUSH
When a bio with REQ_PREFLUSH is submitted to dm, __send_empty_flush()
generates a flush_bio with REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC,
which causes the flush_bio to be throttled by wbt_wait().
An example from v5.4, similar problem also exists in upstream:
crash> bt 2091206
PID: 2091206 TASK: ffff2050df92a300 CPU: 109 COMMAND: "kworker/u260:0"
#0 [ffff800084a2f7f0] __switch_to at ffff80004008aeb8
#1 [ffff800084a2f820] __schedule at ffff800040bfa0c4
#2 [ffff800084a2f880] schedule at ffff800040bfa4b4
#3 [ffff800084a2f8a0] io_schedule at ffff800040bfa9c4
#4 [ffff800084a2f8c0] rq_qos_wait at ffff8000405925bc
#5 [ffff800084a2f940] wbt_wait at ffff8000405bb3a0
#6 [ffff800084a2f9a0] __rq_qos_throttle at ffff800040592254
#7 [ffff800084a2f9c0] blk_mq_make_request at ffff80004057cf38
#8 [ffff800084a2fa60] generic_make_request at ffff800040570138
#9 [ffff800084a2fae0] submit_bio at ffff8000405703b4
#10 [ffff800084a2fb50] xlog_write_iclog at ffff800001280834 [xfs]
#11 [ffff800084a2fbb0] xlog_sync at ffff800001280c3c [xfs]
#12 [ffff800084a2fbf0] xlog_state_release_iclog at ffff800001280df4 [xfs]
#13 [ffff800084a2fc10] xlog_write at ffff80000128203c [xfs]
#14 [ffff800084a2fcd0] xlog_cil_push at ffff8000012846dc [xfs]
#15 [ffff800084a2fda0] xlog_cil_push_work at ffff800001284a2c [xfs]
#16 [ffff800084a2fdb0] process_one_work at ffff800040111d08
#17 [ffff800084a2fe00] worker_thread at ffff8000401121cc
#18 [ffff800084a2fe70] kthread at ffff800040118de4
After commit 2def2845cc33 ("xfs: don't allow log IO to be throttled"),
the metadata submitted by xlog_write_iclog() should not be throttled.
But due to the existence of the dm layer, throttling flush_bio indirectly
causes the metadata bio to be throttled.
Fix this by conditionally adding REQ_IDLE to flush_bio.bi_opf, which makes
wbt_should_throttle() return false to avoid wbt_wait(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: pktgen: fix access outside of user given buffer in pktgen_thread_write()
Honour the user given buffer size for the strn_len() calls (otherwise
strn_len() will access memory outside of the user given buffer). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/fred: Fix system hang during S4 resume with FRED enabled
Upon a wakeup from S4, the restore kernel starts and initializes the
FRED MSRs as needed from its perspective. It then loads a hibernation
image, including the image kernel, and attempts to load image pages
directly into their original page frames used before hibernation unless
those frames are currently in use. Once all pages are moved to their
original locations, it jumps to a "trampoline" page in the image kernel.
At this point, the image kernel takes control, but the FRED MSRs still
contain values set by the restore kernel, which may differ from those
set by the image kernel before hibernation. Therefore, the image kernel
must ensure the FRED MSRs have the same values as before hibernation.
Since these values depend only on the location of the kernel text and
data, they can be recomputed from scratch. |
| In the Linux kernel, the following vulnerability has been resolved:
media: cx231xx: set device_caps for 417
The video_device for the MPEG encoder did not set device_caps.
Add this, otherwise the video device can't be registered (you get a
WARN_ON instead).
Not seen before since currently 417 support is disabled, but I found
this while experimenting with it. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: mctrl_gpio: split disable_ms into sync and no_sync APIs
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Avoid WARN_ON when configuring MQPRIO with HTB offload enabled
When attempting to enable MQPRIO while HTB offload is already
configured, the driver currently returns `-EINVAL` and triggers a
`WARN_ON`, leading to an unnecessary call trace.
Update the code to handle this case more gracefully by returning
`-EOPNOTSUPP` instead, while also providing a helpful user message. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: Annotate FDB data races
The 'used' and 'updated' fields in the FDB entry structure can be
accessed concurrently by multiple threads, leading to reports such as
[1]. Can be reproduced using [2].
Suppress these reports by annotating these accesses using
READ_ONCE() / WRITE_ONCE().
[1]
BUG: KCSAN: data-race in vxlan_xmit / vxlan_xmit
write to 0xffff942604d263a8 of 8 bytes by task 286 on cpu 0:
vxlan_xmit+0xb29/0x2380
dev_hard_start_xmit+0x84/0x2f0
__dev_queue_xmit+0x45a/0x1650
packet_xmit+0x100/0x150
packet_sendmsg+0x2114/0x2ac0
__sys_sendto+0x318/0x330
__x64_sys_sendto+0x76/0x90
x64_sys_call+0x14e8/0x1c00
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff942604d263a8 of 8 bytes by task 287 on cpu 2:
vxlan_xmit+0xadf/0x2380
dev_hard_start_xmit+0x84/0x2f0
__dev_queue_xmit+0x45a/0x1650
packet_xmit+0x100/0x150
packet_sendmsg+0x2114/0x2ac0
__sys_sendto+0x318/0x330
__x64_sys_sendto+0x76/0x90
x64_sys_call+0x14e8/0x1c00
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
value changed: 0x00000000fffbac6e -> 0x00000000fffbac6f
Reported by Kernel Concurrency Sanitizer on:
CPU: 2 UID: 0 PID: 287 Comm: mausezahn Not tainted 6.13.0-rc7-01544-gb4b270f11a02 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014
[2]
#!/bin/bash
set +H
echo whitelist > /sys/kernel/debug/kcsan
echo !vxlan_xmit > /sys/kernel/debug/kcsan
ip link add name vx0 up type vxlan id 10010 dstport 4789 local 192.0.2.1
bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 198.51.100.1
taskset -c 0 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q &
taskset -c 2 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q & |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Refactor remove call with idxd_cleanup() helper
The idxd_cleanup() helper cleans up perfmon, interrupts, internals and
so on. Refactor remove call with the idxd_cleanup() helper to avoid code
duplication. Note, this also fixes the missing put_device() for idxd
groups, enginces and wqs. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: disable napi on driver removal
A warning on driver removal started occurring after commit 9dd05df8403b
("net: warn if NAPI instance wasn't shut down"). Disable tx napi before
deleting it in mt76_dma_cleanup().
WARNING: CPU: 4 PID: 18828 at net/core/dev.c:7288 __netif_napi_del_locked+0xf0/0x100
CPU: 4 UID: 0 PID: 18828 Comm: modprobe Not tainted 6.15.0-rc4 #4 PREEMPT(lazy)
Hardware name: ASUS System Product Name/PRIME X670E-PRO WIFI, BIOS 3035 09/05/2024
RIP: 0010:__netif_napi_del_locked+0xf0/0x100
Call Trace:
<TASK>
mt76_dma_cleanup+0x54/0x2f0 [mt76]
mt7921_pci_remove+0xd5/0x190 [mt7921e]
pci_device_remove+0x47/0xc0
device_release_driver_internal+0x19e/0x200
driver_detach+0x48/0x90
bus_remove_driver+0x6d/0xf0
pci_unregister_driver+0x2e/0xb0
__do_sys_delete_module.isra.0+0x197/0x2e0
do_syscall_64+0x7b/0x160
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Tested with mt7921e but the same pattern can be actually applied to other
mt76 drivers calling mt76_dma_cleanup() during removal. Tx napi is enabled
in their *_dma_init() functions and only toggled off and on again inside
their suspend/resume/reset paths. So it should be okay to disable tx
napi in such a generic way.
Found by Linux Verification Center (linuxtesting.org). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: class: Invalidate USB device pointers on partner unregistration
To avoid using invalid USB device pointers after a Type-C partner
disconnects, this patch clears the pointers upon partner unregistration.
This ensures a clean state for future connections. |
| In the Linux kernel, the following vulnerability has been resolved:
block: integrity: Do not call set_page_dirty_lock()
Placing multiple protection information buffers inside the same page
can lead to oopses because set_page_dirty_lock() can't be called from
interrupt context.
Since a protection information buffer is not backed by a file there is
no point in setting its page dirty, there is nothing to synchronize.
Drop the call to set_page_dirty_lock() and remove the last argument to
bio_integrity_unpin_bvec(). |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: bpf: Only mitigate cBPF programs loaded by unprivileged users
Support for eBPF programs loaded by unprivileged users is typically
disabled. This means only cBPF programs need to be mitigated for BHB.
In addition, only mitigate cBPF programs that were loaded by an
unprivileged user. Privileged users can also load the same program
via eBPF, making the mitigation pointless. |
| In the Linux kernel, the following vulnerability has been resolved:
memblock: Accept allocated memory before use in memblock_double_array()
When increasing the array size in memblock_double_array() and the slab
is not yet available, a call to memblock_find_in_range() is used to
reserve/allocate memory. However, the range returned may not have been
accepted, which can result in a crash when booting an SNP guest:
RIP: 0010:memcpy_orig+0x68/0x130
Code: ...
RSP: 0000:ffffffff9cc03ce8 EFLAGS: 00010006
RAX: ff11001ff83e5000 RBX: 0000000000000000 RCX: fffffffffffff000
RDX: 0000000000000bc0 RSI: ffffffff9dba8860 RDI: ff11001ff83e5c00
RBP: 0000000000002000 R08: 0000000000000000 R09: 0000000000002000
R10: 000000207fffe000 R11: 0000040000000000 R12: ffffffff9d06ef78
R13: ff11001ff83e5000 R14: ffffffff9dba7c60 R15: 0000000000000c00
memblock_double_array+0xff/0x310
memblock_add_range+0x1fb/0x2f0
memblock_reserve+0x4f/0xa0
memblock_alloc_range_nid+0xac/0x130
memblock_alloc_internal+0x53/0xc0
memblock_alloc_try_nid+0x3d/0xa0
swiotlb_init_remap+0x149/0x2f0
mem_init+0xb/0xb0
mm_core_init+0x8f/0x350
start_kernel+0x17e/0x5d0
x86_64_start_reservations+0x14/0x30
x86_64_start_kernel+0x92/0xa0
secondary_startup_64_no_verify+0x194/0x19b
Mitigate this by calling accept_memory() on the memory range returned
before the slab is available.
Prior to v6.12, the accept_memory() interface used a 'start' and 'end'
parameter instead of 'start' and 'size', therefore the accept_memory()
call must be adjusted to specify 'start + size' for 'end' when applying
to kernels prior to v6.12. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: bpf: Add BHB mitigation to the epilogue for cBPF programs
A malicious BPF program may manipulate the branch history to influence
what the hardware speculates will happen next.
On exit from a BPF program, emit the BHB mititgation sequence.
This is only applied for 'classic' cBPF programs that are loaded by
seccomp. |
| In the Linux kernel, the following vulnerability has been resolved:
sch_htb: make htb_qlen_notify() idempotent
htb_qlen_notify() always deactivates the HTB class and in fact could
trigger a warning if it is already deactivated. Therefore, it is not
idempotent and not friendly to its callers, like fq_codel_dequeue().
Let's make it idempotent to ease qdisc_tree_reduce_backlog() callers'
life. |
