| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: make error counter atomic
The error counter "v->corrupted_errs" was not atomic, thus it could be
subject to race conditions. The call to
dm_audit_log_target("max-corrupted-errors") may be skipped due to the
races. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: tegra: do not call pinctrl for GPIO direction
tegra_gpio_direction_input() and tegra_gpio_direction_output() already
program the GPIO controller direction registers directly. The additional
pinctrl_gpio_direction_input/output() calls do not add a Tegra pinctrl
operation, because the Tegra pinmux ops provide GPIO request/free
handling but no gpio_set_direction hook.
The extra call still enters the pinctrl core and takes pctldev->mutex.
Shared GPIO users can call the direction path while holding their
per-line spinlock, so this otherwise redundant pinctrl direction call can
sleep in an atomic context.
This was found by our static analysis tool and then confirmed by manual
review of tegra_gpio_probe(), the Tegra GPIO direction callbacks and the
Tegra pinctrl ops. The reviewed path has a default non-sleeping
struct gpio_chip while the direction callback still enters the pinctrl
mutex path.
A directed runtime validation kept the same non-sleeping chip registration
and drove:
gpio_shared_proxy_direction_output()
gpiod_direction_output_raw_commit()
tegra_gpio_direction_output()
pinctrl_gpio_direction_output()
Lockdep reported a sleep-in-atomic warning with the shared GPIO spinlock
held and pinctrl_get_device_gpio_range() plus tegra_gpio_direction_output()
on the stack.
Do not mark the whole chip as can_sleep to paper over this: can_sleep
describes whether get()/set() may sleep, and Tegra value access is MMIO.
Remove the redundant pinctrl direction calls and keep pinctrl involvement
in the existing request/free path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx8: drop unecessary BUG_ON()
There's no need to crash the kernel for this case.
(cherry picked from commit 4d7c25208ca612b754f3bf39e9f16e725b828891) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: wake eh reliably when using scsi_schedule_eh
Drivers which use the scsi_schedule_eh function to run the error handler
currently risk the error handler thread never waking once all commands are
timed out or inactive. There is no enforced memory order between setting
the host into error recovery state and counting busy commands. This can
result in a race with scsi_dec_host_busy where neither CPU sees both
conditions of all commands inactive and the host error state to request
waking the error handler.
To fix this, run the scsi_schedule_eh's scsi_eh_wakeup from a new work item
which will use rcu to ensure scsi_schedule_eh's call to scsi_host_busy will
occur after the error state is globally visible and will be seen by any
current scsi_dec_host_busy callers. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix 802.1X-SHA256 call trace warning
Based on wpa_auth as 1x_256 mode, need to set up
"use_fwsup" with BRCMF_PROFILE_FWSUP_1X.
Or it will happen trace warning when call brcmf_cfg80211_set_pmk().
[ 4481.831101] ------------[ cut here ]------------
[ 4481.831102] WARNING: CPU: 1 PID: 2997 at
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:7242 brcmf_cfg80211_set_pmk+0x77/0xd0 [brcmfmac]
[...]
[ 4481.831202] Call Trace:
[ 4481.831204] <TASK>
[ 4481.831205] nl80211_set_pmk+0x183/0x250 [cfg80211]
[ 4481.831233] genl_family_rcv_msg_doit+0xea/0x150
[ 4481.831237] genl_rcv_msg+0x104/0x240
[ 4481.831239] ? cfg80211_probe_status+0x2c0/0x2c0 [cfg80211]
[ 4481.831257] ? genl_family_rcv_msg_doit+0x150/0x150
[ 4481.831259] netlink_rcv_skb+0x4e/0x100
[ 4481.831261] genl_rcv+0x24/0x40
[ 4481.831262] netlink_unicast+0x236/0x380
[ 4481.831264] netlink_sendmsg+0x250/0x4b0
[ 4481.831266] sock_sendmsg+0x5c/0x70
[ 4481.831269] ____sys_sendmsg+0x236/0x2b0
[ 4481.831271] ? copy_msghdr_from_user+0x6d/0xa0
[ 4481.831272] ___sys_sendmsg+0x86/0xd0
[ 4481.831274] ? avc_has_perm+0x8c/0x1a0
[ 4481.831276] ? preempt_count_add+0x6a/0xa0
[ 4481.831279] ? sock_has_perm+0x82/0xa0
[ 4481.831280] __sys_sendmsg+0x57/0xa0
[ 4481.831282] do_syscall_64+0x38/0x90
[ 4481.831284] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 4481.831286] RIP: 0033:0x7fd270d369b4 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/sdma5.2: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit ae658afc7f47f6147371ec42cc6b1a793dfdb5af) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/sdma5.0: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit 8d144a0eb09537055841af48c9e7c2d4cd48e84d) |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix PTP Call Trace during PTP release
If a PF reset occurs when the PTP state is ICE_PTP_UNINIT, then
ice_ptp_rebuild() will update the state to ICE_PTP_ERROR. This will
result in the following PTP release call trace during driver unload:
kernel BUG at lib/list_debug.c:52!
ice_ptp_release+0x332/0x3c0 [ice]
ice_deinit_features.part.0+0x10e/0x120 [ice]
ice_remove+0x100/0x220 [ice]
This was observed when passing PF1 through to a VM. ice_ptp_init()
fails because ctrl_pf is NULL and sets the state to ICE_PTP_UNINIT.
Fix by detecting the ICE_PTP_UNINIT state in ice_ptp_rebuild() and
returning without error, preventing the invalid state transition to
ICE_PTP_ERROR. The only valid path to ICE_PTP_ERROR is from
ICE_PTP_RESETTING after a failed rebuild. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx10: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit ac6f00beb658239bced4aaed9efbb04a35348d48) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx9: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit b71604f8685b0eba07866f4e8dc30f93e1931054) |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Bump asid_generation on CPU online to avoid ASID collision after hotplug
If a vCPU stays scheduled out (or blocked) while the last pCPU it ran
on goes through a hotplug cycle (online->offline->online), and the vCPU
then resumes execution on the same pCPU, then it is possible for it to
run with an ASID that has now been assigned to a different vCPU,
resulting in stale TLB translations being used.
svm_enable_virtualization_cpu() resets asid_generation to 1 and sets
next_asid to max_asid + 1 on every CPU online event, including hotplug
cycles. Because next_asid starts beyond the pool boundary, the first
call to new_asid() after an online event always wraps the pool,
incrementing asid_generation to 2 and assigning ASIDs starting from
min_asid.
Consider two vCPUs from different VMs, vCPU-A pinned to CPU-X holding
asid_generation=2 and ASID=N from before the hotplug event:
1. CPU-X goes offline and back online: asid_generation resets to 1,
next_asid = max_asid + 1.
2. One or more vCPUs migrate to CPU-X and call new_asid(), wrapping
the pool and consuming ASIDs starting from min_asid. Eventually
vCPU-B from a different VM is assigned asid_generation=2, ASID=N
— the same ASID that vCPU-A held before the hotplug.
3. vCPU-A enters pre_svm_run() on CPU-X: current_vmcb->cpu is
unchanged so the migration branch is skipped. Its saved
asid_generation=2 matches sd->asid_generation=2, so the generation
check silently passes and vCPU-A continues running with ASID=N —
the same ASID just freshly assigned to vCPU-B.
Both vCPUs from different VMs now run on CPU-X with the same ASID,
causing them to share NPT TLB entries and producing stale translations.
The collision manifests as a KVM internal error (Suberror: 1, emulation
failure). The NPT page fault reports a faulting GPA far outside the
VM's physical memory range — a sign of stale TLB translations being
used. KVM falls back to instruction emulation, which fails on
FPU/XSave instructions (XRSTOR, STMXCSR) that the emulator does not
implement.
Fix this by incrementing asid_generation instead of resetting it to 1
in svm_enable_virtualization_cpu(). On module load, asid_generation
starts at 0 (memset) and the increment produces 1, identical to the
old behaviour. On subsequent hotplug cycles the generation advances
beyond any value a vCPU previously observed on this CPU, so the
generation check in pre_svm_run() reliably forces new_asid() on every
vCPU after every hotplug cycle. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: asymmetric_keys - fix OOB read in pefile_digest_pe_contents
pefile_digest_pe_contents() computes the trailing-data hash length as
pelen - (hashed_bytes + certs_size). A crafted PE can make the addition
exceed pelen, causing the unsigned subtraction to underflow to ~4 GiB.
This is passed to crypto_shash_update() which reads out of bounds and
panics on unmapped vmalloc guard pages.
BUG: unable to handle page fault for address: ffffc900038d8000
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:sha256_blocks_generic (lib/crypto/sha256.c:152)
Call Trace:
<TASK>
__sha256_update (lib/crypto/sha256.c:208)
crypto_sha256_update (crypto/sha256.c:142)
verify_pefile_signature (crypto/asymmetric_keys/verify_pefile.c:436)
kexec_kernel_verify_pe_sig (kernel/kexec_file.c:151)
__do_sys_kexec_file_load (kernel/kexec_file.c:406)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
</TASK>
Kernel panic - not syncing: Fatal exception
Validate that the addition does not overflow and the result does not
exceed pelen before the subtraction. Return -ELIBBAD on failure. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/mlx5: Fix racy bitfields and tighten struct layout
Bitfield operations are not atomic, they use a read-modify-write
pattern, therefore we should be careful not to pack bitfields that
can be concurrently updated into the same storage unit.
This split takes a binary approach: flags that are only modified
pre/post open/close remain bitfields, flags modified from user
action, including actions that reach across to another device (ex.
reset) use dedicated storage units.
Note mlx5_vhca_page_tracker.status is relocated to fill the alignment
hole this split exposes.
Bitfield justifications:
migrate_cap: written only in mlx5vf_cmd_set_migratable() at probe
chunk_mode: written only in mlx5vf_cmd_set_migratable() at probe
mig_state_cap: written only in mlx5vf_cmd_set_migratable() at probe
Dedicated storage units:
mdev_detach: written in the VF attach/detach event notifier
mlx5fv_vf_event() at runtime
log_active: written in mlx5vf_start_page_tracker()/
mlx5vf_stop_page_tracker() during runtime dirty tracking
deferred_reset: written in mlx5vf_state_mutex_unlock()/
mlx5vf_pci_aer_reset_done() during runtime reset handling
is_err: set by tracker error handling and dirty-log polling at runtime
object_changed: set by tracker event handling and cleared by dirty-log
polling at runtime |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: run gadget disconnect from sleepable suspend context
dwc3_gadget_suspend() takes dwc->lock with IRQs disabled and then calls
dwc3_disconnect_gadget(). For async callbacks that helper only uses
plain spin_unlock()/spin_lock(), so the gadget ->disconnect() callback
still runs with IRQs disabled and any sleepable callback trips Lockdep.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the dwc3_gadget_suspend() ->
dwc3_disconnect_gadget() -> gadget_driver->disconnect() chain, and
Lockdep reported:
BUG: sleeping function called from invalid context
gadget_disconnect+0x21/0x39 [vuln_msv]
dwc3_gadget_suspend.constprop.0+0x2b/0x42 [vuln_msv]
Keep the disconnect callback selection in one common helper, but add a
sleepable suspend-side wrapper which snapshots the callback under
dwc->lock and then runs it after spin_unlock_irqrestore(). The regular
event path still uses the existing spin_unlock()/spin_lock() window. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix dead empty check in the USB_DT_OTG handler
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: digi_acceleport: fix hard lockup on disconnect
If submitting the OOB write urb fails persistently (e.g if the device is
being disconnected) the driver would loop indefinitely with interrupts
disabled.
Check for urb submission errors when sending OOB commands to avoid
hanging if, for example, open(), set_termios() or close() races with a
physical disconnect.
This is issue was flagged by Sashiko when reviewing an unrelated change
to the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Set upper bounds on cache invalidation entry_num and entry_len
iommufd_hwpt_invalidate() takes a user-controlled entry_num and entry_len,
each bounded only by U32_MAX. An entry_len beyond the kernel's struct size
makes the copy helper verify the extra bytes are zero, scanning that excess
in one uninterruptible pass; a multi-gigabyte value over zeroed user memory
trips the soft-lockup watchdog.
A large entry_num is the other half, driving the backend invalidation loop
with no reschedule. The VT-d nested handler, for one, copies each entry and
flushes caches per iteration, pinning the CPU on a non-preemptible kernel.
Cap both in the ioctl. entry_len is held under PAGE_SIZE, above any request
struct, and entry_num under 1 << 19, the order of a hardware invalidation
queue and well beyond any real batch, bounding the per-call loop length. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: tegra: fix pm_runtime leak on mutex_lock failure
If tegra_i2c_mutex_lock() fails, the function returns without calling
pm_runtime_put(), leaking the runtime PM reference acquired by the
preceding pm_runtime_get_sync(). This prevents the device from ever
entering runtime suspend.
Add the missing pm_runtime_put() before returning on lock failure. |
| ZAC is an open-source, workflow-based Common Ground component for Dutch municipal case management. Prior to 5.2.0, by-id read endpoints in `src/main/kotlin/nl/info/zac/app/zaak/ZaakRestService.kt` omit `assertPolicy`(`policyService.readZaakRechten(zaak).lezen`) authorization. `RequestAuthorizationFilter` and `hasAnyApplicationRole` require only an application role on any zaaktype, not the target case's type, while `zaak-rechten.rego` enforces the actual `zaaktype_allowed` boundary only when invoked. An authenticated low-privileged municipal user who knows a case or decision UUID can use `GET /rest/zaken/besluit/zaakUuid/{uuid}` (`listBesluitenForZaakUUID`) to read decisions including types, dates, and free-text toelichting; `GET /rest/zaken/besluit/{uuid}/historie` (`listBesluitHistorie`) to read audit old/new values; and `GET /rest/zaken/{uuid}/process-diagram` (`downloadProcessDiagram`) to read BPMN workflow state across unauthorized zaaktypes. The advisory also identifies `zaak/{uuid}/afzender` (`listAfzendersVoorZaak`) as exposing zaaktype mailbox configuration without a policy check. The search/_zoek path is correctly authorization-filtered and is not part of this by-id read cluster. This issue is fixed in version 5.2.0. |
| In the Linux kernel, the following vulnerability has been resolved:
signal: clear JOBCTL_PENDING_MASK for caller in zap_other_threads()
When a multi-threaded process receives a stop signal (e.g., SIGSTOP),
do_signal_stop() sets JOBCTL_STOP_PENDING and JOBCTL_STOP_CONSUME on all
threads and sets signal->group_stop_count to the number of threads. If
one of the threads concurrently calls execve(), de_thread() invokes
zap_other_threads() to kill all other threads. zap_other_threads()
aborts the pending group stop by resetting signal->group_stop_count to 0
and clears the JOBCTL_PENDING_MASK for all other threads. However, it
fails to clear the job control flags for the calling thread.
When execve() completes, the calling thread returns to user mode and
checks for pending signals. Seeing the stale JOBCTL_STOP_PENDING flag,
it calls do_signal_stop(), which invokes task_participate_group_stop().
Since JOBCTL_STOP_CONSUME is still set, it attempts to decrement the
already-zero signal->group_stop_count, triggering a warning:
sig->group_stop_count == 0
WARNING: CPU: 1 PID: 6475 at kernel/signal.c:373
task_participate_group_stop+0x215/0x2d0
Call Trace:
<TASK>
do_signal_stop+0x3be/0x5c0 kernel/signal.c:2619
get_signal+0xa8c/0x1330 kernel/signal.c:2884
arch_do_signal_or_restart+0xbc/0x840 arch/x86/kernel/signal.c:337
exit_to_user_mode_loop+0x8c/0x4d0 kernel/entry/common.c:98
do_syscall_64+0x33e/0xf80 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Fix this race condition by clearing the JOBCTL_PENDING_MASK for the
calling thread in zap_other_threads(), ensuring it does not retain any
stale job control state after the thread group is destroyed. This aligns
with other functions that tear down a thread group and abort group
stops, such as zap_process() and complete_signal(), which correctly
clear these flags for all threads including the current one. |
