| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/firmware: Add missing kfree() of nvkm_falcon_fw::boot
nvkm_falcon_fw::boot is allocated, but no one frees it. This causes a
kmemleak warning.
Make sure this data is deallocated. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv4: fix one memleak in __inet_del_ifa()
I got the below warning when do fuzzing test:
unregister_netdevice: waiting for bond0 to become free. Usage count = 2
It can be repoduced via:
ip link add bond0 type bond
sysctl -w net.ipv4.conf.bond0.promote_secondaries=1
ip addr add 4.117.174.103/0 scope 0x40 dev bond0
ip addr add 192.168.100.111/255.255.255.254 scope 0 dev bond0
ip addr add 0.0.0.4/0 scope 0x40 secondary dev bond0
ip addr del 4.117.174.103/0 scope 0x40 dev bond0
ip link delete bond0 type bond
In this reproduction test case, an incorrect 'last_prim' is found in
__inet_del_ifa(), as a result, the secondary address(0.0.0.4/0 scope 0x40)
is lost. The memory of the secondary address is leaked and the reference of
in_device and net_device is leaked.
Fix this problem:
Look for 'last_prim' starting at location of the deleted IP and inserting
the promoted IP into the location of 'last_prim'. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/namespace: fix reference leak in grab_requested_mnt_ns
lookup_mnt_ns() already takes a reference on mnt_ns.
grab_requested_mnt_ns() doesn't need to take an extra reference. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pci: Avoid deadlock between PCI error recovery and mlx5 crdump
Do not block PCI config accesses through pci_cfg_access_lock() when
executing the s390 variant of PCI error recovery: Acquire just
device_lock() instead of pci_dev_lock() as powerpc's EEH and
generig PCI AER processing do.
During error recovery testing a pair of tasks was reported to be hung:
mlx5_core 0000:00:00.1: mlx5_health_try_recover:338:(pid 5553): health recovery flow aborted, PCI reads still not working
INFO: task kmcheck:72 blocked for more than 122 seconds.
Not tainted 5.14.0-570.12.1.bringup7.el9.s390x #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kmcheck state:D stack:0 pid:72 tgid:72 ppid:2 flags:0x00000000
Call Trace:
[<000000065256f030>] __schedule+0x2a0/0x590
[<000000065256f356>] schedule+0x36/0xe0
[<000000065256f572>] schedule_preempt_disabled+0x22/0x30
[<0000000652570a94>] __mutex_lock.constprop.0+0x484/0x8a8
[<000003ff800673a4>] mlx5_unload_one+0x34/0x58 [mlx5_core]
[<000003ff8006745c>] mlx5_pci_err_detected+0x94/0x140 [mlx5_core]
[<0000000652556c5a>] zpci_event_attempt_error_recovery+0xf2/0x398
[<0000000651b9184a>] __zpci_event_error+0x23a/0x2c0
INFO: task kworker/u1664:6:1514 blocked for more than 122 seconds.
Not tainted 5.14.0-570.12.1.bringup7.el9.s390x #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u1664:6 state:D stack:0 pid:1514 tgid:1514 ppid:2 flags:0x00000000
Workqueue: mlx5_health0000:00:00.0 mlx5_fw_fatal_reporter_err_work [mlx5_core]
Call Trace:
[<000000065256f030>] __schedule+0x2a0/0x590
[<000000065256f356>] schedule+0x36/0xe0
[<0000000652172e28>] pci_wait_cfg+0x80/0xe8
[<0000000652172f94>] pci_cfg_access_lock+0x74/0x88
[<000003ff800916b6>] mlx5_vsc_gw_lock+0x36/0x178 [mlx5_core]
[<000003ff80098824>] mlx5_crdump_collect+0x34/0x1c8 [mlx5_core]
[<000003ff80074b62>] mlx5_fw_fatal_reporter_dump+0x6a/0xe8 [mlx5_core]
[<0000000652512242>] devlink_health_do_dump.part.0+0x82/0x168
[<0000000652513212>] devlink_health_report+0x19a/0x230
[<000003ff80075a12>] mlx5_fw_fatal_reporter_err_work+0xba/0x1b0 [mlx5_core]
No kernel log of the exact same error with an upstream kernel is
available - but the very same deadlock situation can be constructed there,
too:
- task: kmcheck
mlx5_unload_one() tries to acquire devlink lock while the PCI error
recovery code has set pdev->block_cfg_access by way of
pci_cfg_access_lock()
- task: kworker
mlx5_crdump_collect() tries to set block_cfg_access through
pci_cfg_access_lock() while devlink_health_report() had acquired
the devlink lock.
A similar deadlock situation can be reproduced by requesting a
crdump with
> devlink health dump show pci/<BDF> reporter fw_fatal
while PCI error recovery is executed on the same <BDF> physical function
by mlx5_core's pci_error_handlers. On s390 this can be injected with
> zpcictl --reset-fw <BDF>
Tests with this patch failed to reproduce that second deadlock situation,
the devlink command is rejected with "kernel answers: Permission denied" -
and we get a kernel log message of:
mlx5_core 1ed0:00:00.1: mlx5_crdump_collect:50:(pid 254382): crdump: failed to lock vsc gw err -5
because the config read of VSC_SEMAPHORE is rejected by the underlying
hardware.
Two prior attempts to address this issue have been discussed and
ultimately rejected [see link], with the primary argument that s390's
implementation of PCI error recovery is imposing restrictions that
neither powerpc's EEH nor PCI AER handling need. Tests show that PCI
error recovery on s390 is running to completion even without blocking
access to PCI config space. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix invalid probe error return value
After DME Link Startup, the error return value is set to the MIPI UniPro
GenericErrorCode which can be 0 (SUCCESS) or 1 (FAILURE). Upon failure
during driver probe, the error code 1 is propagated back to the driver
probe function which must return a negative value to indicate an error,
but 1 is not negative, so the probe is considered to be successful even
though it failed. Subsequently, removing the driver results in an oops
because it is not in a valid state.
This happens because none of the callers of ufshcd_init() expect a
non-negative error code.
Fix the return value and documentation to match actual usage. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: potential integer overflow in usbg_make_tpg()
The variable tpgt in usbg_make_tpg() is defined as unsigned long and is
assigned to tpgt->tport_tpgt, which is defined as u16. This may cause an
integer overflow when tpgt is greater than USHRT_MAX (65535). I
haven't tried to trigger it myself, but it is possible to trigger it
by calling usbg_make_tpg() with a large value for tpgt.
I modified the type of tpgt to match tpgt->tport_tpgt and adjusted the
relevant code accordingly.
This patch is similar to commit 59c816c1f24d ("vhost/scsi: potential
memory corruption"). |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: virtio - Fix race on data_avail and actual data
The virtio rng device kicks off a new entropy request whenever the
data available reaches zero. When a new request occurs at the end
of a read operation, that is, when the result of that request is
only needed by the next reader, then there is a race between the
writing of the new data and the next reader.
This is because there is no synchronisation whatsoever between the
writer and the reader.
Fix this by writing data_avail with smp_store_release and reading
it with smp_load_acquire when we first enter read. The subsequent
reads are safe because they're either protected by the first load
acquire, or by the completion mechanism.
Also remove the redundant zeroing of data_idx in random_recv_done
(data_idx must already be zero at this point) and data_avail in
request_entropy (ditto). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/fpu: Fix false-positive kmsan report in fpu_vstl()
A false-positive kmsan report is detected when running ping command.
An inline assembly instruction 'vstl' can write varied amount of bytes
depending on value of 'index' argument. If 'index' > 0, 'vstl' writes
at least 2 bytes.
clang generates kmsan write helper call depending on inline assembly
constraints. Constraints are evaluated compile-time, but value of
'index' argument is known only at runtime.
clang currently generates call to __msan_instrument_asm_store with 1 byte
as size. Manually call kmsan function to indicate correct amount of bytes
written and fix false-positive report.
This change fixes following kmsan reports:
[ 36.563119] =====================================================
[ 36.563594] BUG: KMSAN: uninit-value in virtqueue_add+0x35c6/0x7c70
[ 36.563852] virtqueue_add+0x35c6/0x7c70
[ 36.564016] virtqueue_add_outbuf+0xa0/0xb0
[ 36.564266] start_xmit+0x288c/0x4a20
[ 36.564460] dev_hard_start_xmit+0x302/0x900
[ 36.564649] sch_direct_xmit+0x340/0xea0
[ 36.564894] __dev_queue_xmit+0x2e94/0x59b0
[ 36.565058] neigh_resolve_output+0x936/0xb40
[ 36.565278] __neigh_update+0x2f66/0x3a60
[ 36.565499] neigh_update+0x52/0x60
[ 36.565683] arp_process+0x1588/0x2de0
[ 36.565916] NF_HOOK+0x1da/0x240
[ 36.566087] arp_rcv+0x3e4/0x6e0
[ 36.566306] __netif_receive_skb_list_core+0x1374/0x15a0
[ 36.566527] netif_receive_skb_list_internal+0x1116/0x17d0
[ 36.566710] napi_complete_done+0x376/0x740
[ 36.566918] virtnet_poll+0x1bae/0x2910
[ 36.567130] __napi_poll+0xf4/0x830
[ 36.567294] net_rx_action+0x97c/0x1ed0
[ 36.567556] handle_softirqs+0x306/0xe10
[ 36.567731] irq_exit_rcu+0x14c/0x2e0
[ 36.567910] do_io_irq+0xd4/0x120
[ 36.568139] io_int_handler+0xc2/0xe8
[ 36.568299] arch_cpu_idle+0xb0/0xc0
[ 36.568540] arch_cpu_idle+0x76/0xc0
[ 36.568726] default_idle_call+0x40/0x70
[ 36.568953] do_idle+0x1d6/0x390
[ 36.569486] cpu_startup_entry+0x9a/0xb0
[ 36.569745] rest_init+0x1ea/0x290
[ 36.570029] start_kernel+0x95e/0xb90
[ 36.570348] startup_continue+0x2e/0x40
[ 36.570703]
[ 36.570798] Uninit was created at:
[ 36.571002] kmem_cache_alloc_node_noprof+0x9e8/0x10e0
[ 36.571261] kmalloc_reserve+0x12a/0x470
[ 36.571553] __alloc_skb+0x310/0x860
[ 36.571844] __ip_append_data+0x483e/0x6a30
[ 36.572170] ip_append_data+0x11c/0x1e0
[ 36.572477] raw_sendmsg+0x1c8c/0x2180
[ 36.572818] inet_sendmsg+0xe6/0x190
[ 36.573142] __sys_sendto+0x55e/0x8e0
[ 36.573392] __s390x_sys_socketcall+0x19ae/0x2ba0
[ 36.573571] __do_syscall+0x12e/0x240
[ 36.573823] system_call+0x6e/0x90
[ 36.573976]
[ 36.574017] Byte 35 of 98 is uninitialized
[ 36.574082] Memory access of size 98 starts at 0000000007aa0012
[ 36.574218]
[ 36.574325] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G B N 6.17.0-dirty #16 NONE
[ 36.574541] Tainted: [B]=BAD_PAGE, [N]=TEST
[ 36.574617] Hardware name: IBM 3931 A01 703 (KVM/Linux)
[ 36.574755] =====================================================
[ 63.532541] =====================================================
[ 63.533639] BUG: KMSAN: uninit-value in virtqueue_add+0x35c6/0x7c70
[ 63.533989] virtqueue_add+0x35c6/0x7c70
[ 63.534940] virtqueue_add_outbuf+0xa0/0xb0
[ 63.535861] start_xmit+0x288c/0x4a20
[ 63.536708] dev_hard_start_xmit+0x302/0x900
[ 63.537020] sch_direct_xmit+0x340/0xea0
[ 63.537997] __dev_queue_xmit+0x2e94/0x59b0
[ 63.538819] neigh_resolve_output+0x936/0xb40
[ 63.539793] ip_finish_output2+0x1ee2/0x2200
[ 63.540784] __ip_finish_output+0x272/0x7a0
[ 63.541765] ip_finish_output+0x4e/0x5e0
[ 63.542791] ip_output+0x166/0x410
[ 63.543771] ip_push_pending_frames+0x1a2/0x470
[ 63.544753] raw_sendmsg+0x1f06/0x2180
[ 63.545033] inet_sendmsg+0xe6/0x190
[ 63.546006] __sys_sendto+0x55e/0x8e0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
Input: pegasus-notetaker - fix potential out-of-bounds access
In the pegasus_notetaker driver, the pegasus_probe() function allocates
the URB transfer buffer using the wMaxPacketSize value from
the endpoint descriptor. An attacker can use a malicious USB descriptor
to force the allocation of a very small buffer.
Subsequently, if the device sends an interrupt packet with a specific
pattern (e.g., where the first byte is 0x80 or 0x42),
the pegasus_parse_packet() function parses the packet without checking
the allocated buffer size. This leads to an out-of-bounds memory access. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: fix deadlock issue when externel_lb and reset are executed together
When externel_lb and reset are executed together, a deadlock may
occur:
[ 3147.217009] INFO: task kworker/u321:0:7 blocked for more than 120 seconds.
[ 3147.230483] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 3147.238999] task:kworker/u321:0 state:D stack: 0 pid: 7 ppid: 2 flags:0x00000008
[ 3147.248045] Workqueue: hclge hclge_service_task [hclge]
[ 3147.253957] Call trace:
[ 3147.257093] __switch_to+0x7c/0xbc
[ 3147.261183] __schedule+0x338/0x6f0
[ 3147.265357] schedule+0x50/0xe0
[ 3147.269185] schedule_preempt_disabled+0x18/0x24
[ 3147.274488] __mutex_lock.constprop.0+0x1d4/0x5dc
[ 3147.279880] __mutex_lock_slowpath+0x1c/0x30
[ 3147.284839] mutex_lock+0x50/0x60
[ 3147.288841] rtnl_lock+0x20/0x2c
[ 3147.292759] hclge_reset_prepare+0x68/0x90 [hclge]
[ 3147.298239] hclge_reset_subtask+0x88/0xe0 [hclge]
[ 3147.303718] hclge_reset_service_task+0x84/0x120 [hclge]
[ 3147.309718] hclge_service_task+0x2c/0x70 [hclge]
[ 3147.315109] process_one_work+0x1d0/0x490
[ 3147.319805] worker_thread+0x158/0x3d0
[ 3147.324240] kthread+0x108/0x13c
[ 3147.328154] ret_from_fork+0x10/0x18
In externel_lb process, the hns3 driver call napi_disable()
first, then the reset happen, then the restore process of the
externel_lb will fail, and will not call napi_enable(). When
doing externel_lb again, napi_disable() will be double call,
cause a deadlock of rtnl_lock().
This patch use the HNS3_NIC_STATE_DOWN state to protect the
calling of napi_disable() and napi_enable() in externel_lb
process, just as the usage in ndo_stop() and ndo_start(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix workqueue leak on bind errors
Make sure to destroy the workqueue also in case of early errors during
bind (e.g. a subcomponent failing to bind).
Since commit c3b790ea07a1 ("drm: Manage drm_mode_config_init with
drmm_") the mode config will be freed when the drm device is released
also when using the legacy interface, but add an explicit cleanup for
consistency and to facilitate backporting.
Patchwork: https://patchwork.freedesktop.org/patch/525093/ |
| In the Linux kernel, the following vulnerability has been resolved:
ns: initialize ns_list_node for initial namespaces
Make sure that the list is always initialized for initial namespaces. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix assertion of exclop condition when starting balance
Balance as exclusive state is compatible with paused balance and device
add, which makes some things more complicated. The assertion of valid
states when starting from paused balance needs to take into account two
more states, the combinations can be hit when there are several threads
racing to start balance and device add. This won't typically happen when
the commands are started from command line.
Scenario 1: With exclusive_operation state == BTRFS_EXCLOP_NONE.
Concurrently adding multiple devices to the same mount point and
btrfs_exclop_finish executed finishes before assertion in
btrfs_exclop_balance, exclusive_operation will changed to
BTRFS_EXCLOP_NONE state which lead to assertion failed:
fs_info->exclusive_operation == BTRFS_EXCLOP_BALANCE ||
fs_info->exclusive_operation == BTRFS_EXCLOP_DEV_ADD,
in fs/btrfs/ioctl.c:456
Call Trace:
<TASK>
btrfs_exclop_balance+0x13c/0x310
? memdup_user+0xab/0xc0
? PTR_ERR+0x17/0x20
btrfs_ioctl_add_dev+0x2ee/0x320
btrfs_ioctl+0x9d5/0x10d0
? btrfs_ioctl_encoded_write+0xb80/0xb80
__x64_sys_ioctl+0x197/0x210
do_syscall_64+0x3c/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Scenario 2: With exclusive_operation state == BTRFS_EXCLOP_BALANCE_PAUSED.
Concurrently adding multiple devices to the same mount point and
btrfs_exclop_balance executed finish before the latter thread execute
assertion in btrfs_exclop_balance, exclusive_operation will changed to
BTRFS_EXCLOP_BALANCE_PAUSED state which lead to assertion failed:
fs_info->exclusive_operation == BTRFS_EXCLOP_BALANCE ||
fs_info->exclusive_operation == BTRFS_EXCLOP_DEV_ADD ||
fs_info->exclusive_operation == BTRFS_EXCLOP_NONE,
fs/btrfs/ioctl.c:458
Call Trace:
<TASK>
btrfs_exclop_balance+0x240/0x410
? memdup_user+0xab/0xc0
? PTR_ERR+0x17/0x20
btrfs_ioctl_add_dev+0x2ee/0x320
btrfs_ioctl+0x9d5/0x10d0
? btrfs_ioctl_encoded_write+0xb80/0xb80
__x64_sys_ioctl+0x197/0x210
do_syscall_64+0x3c/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
An example of the failed assertion is below, which shows that the
paused balance is also needed to be checked.
root@syzkaller:/home/xsk# ./repro
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
[ 416.611428][ T7970] BTRFS info (device loop0): fs_info exclusive_operation: 0
Failed to add device /dev/vda, errno 14
[ 416.613973][ T7971] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.615456][ T7972] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.617528][ T7973] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.618359][ T7974] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.622589][ T7975] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.624034][ T7976] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.626420][ T7977] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.627643][ T7978] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.629006][ T7979] BTRFS info (device loop0): fs_info exclusive_operation: 3
[ 416.630298][ T7980] BTRFS info (device loop0): fs_info exclusive_operation: 3
Fai
---truncated--- |
| Nokia SR Linux is vulnerable to an authentication vulnerability allowing unauthorized access to the JSON-RPC service. When exploited, an invalid validation allows JSON RPC access without providing valid authentication credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Add bpf_prog_run_data_pointers()
syzbot found that cls_bpf_classify() is able to change
tc_skb_cb(skb)->drop_reason triggering a warning in sk_skb_reason_drop().
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 __sk_skb_reason_drop net/core/skbuff.c:1189 [inline]
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 sk_skb_reason_drop+0x76/0x170 net/core/skbuff.c:1214
struct tc_skb_cb has been added in commit ec624fe740b4 ("net/sched:
Extend qdisc control block with tc control block"), which added a wrong
interaction with db58ba459202 ("bpf: wire in data and data_end for
cls_act_bpf").
drop_reason was added later.
Add bpf_prog_run_data_pointers() helper to save/restore the net_sched
storage colliding with BPF data_meta/data_end. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix NULL-deref on snapshot tear down
In case of early initialisation errors and on platforms that do not use
the DPU controller, the deinitilisation code can be called with the kms
pointer set to NULL.
Patchwork: https://patchwork.freedesktop.org/patch/525099/ |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix divide-by-zero in exfat_allocate_bitmap
The variable max_ra_count can be 0 in exfat_allocate_bitmap(),
which causes a divide-by-zero error in the subsequent modulo operation
(i % max_ra_count), leading to a system crash.
When max_ra_count is 0, it means that readahead is not used. This patch
load the bitmap without readahead. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Fix data-race around unix_tot_inflight.
unix_tot_inflight is changed under spin_lock(unix_gc_lock), but
unix_release_sock() reads it locklessly.
Let's use READ_ONCE() for unix_tot_inflight.
Note that the writer side was marked by commit 9d6d7f1cb67c ("af_unix:
annote lockless accesses to unix_tot_inflight & gc_in_progress")
BUG: KCSAN: data-race in unix_inflight / unix_release_sock
write (marked) to 0xffffffff871852b8 of 4 bytes by task 123 on cpu 1:
unix_inflight+0x130/0x180 net/unix/scm.c:64
unix_attach_fds+0x137/0x1b0 net/unix/scm.c:123
unix_scm_to_skb net/unix/af_unix.c:1832 [inline]
unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1955
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0x148/0x160 net/socket.c:747
____sys_sendmsg+0x4e4/0x610 net/socket.c:2493
___sys_sendmsg+0xc6/0x140 net/socket.c:2547
__sys_sendmsg+0x94/0x140 net/socket.c:2576
__do_sys_sendmsg net/socket.c:2585 [inline]
__se_sys_sendmsg net/socket.c:2583 [inline]
__x64_sys_sendmsg+0x45/0x50 net/socket.c:2583
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
read to 0xffffffff871852b8 of 4 bytes by task 4891 on cpu 0:
unix_release_sock+0x608/0x910 net/unix/af_unix.c:671
unix_release+0x59/0x80 net/unix/af_unix.c:1058
__sock_release+0x7d/0x170 net/socket.c:653
sock_close+0x19/0x30 net/socket.c:1385
__fput+0x179/0x5e0 fs/file_table.c:321
____fput+0x15/0x20 fs/file_table.c:349
task_work_run+0x116/0x1a0 kernel/task_work.c:179
resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
exit_to_user_mode_prepare+0x174/0x180 kernel/entry/common.c:204
__syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
syscall_exit_to_user_mode+0x1a/0x30 kernel/entry/common.c:297
do_syscall_64+0x4b/0x90 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x72/0xdc
value changed: 0x00000000 -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 4891 Comm: systemd-coredum Not tainted 6.4.0-rc5-01219-gfa0e21fa4443 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 |
| In the Linux kernel, the following vulnerability has been resolved:
clk: clocking-wizard: Fix Oops in clk_wzrd_register_divider()
Smatch detected this potential error pointer dereference
clk_wzrd_register_divider(). If devm_clk_hw_register() fails then
it sets "hw" to an error pointer and then dereferences it on the
next line. Return the error directly instead. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: bridge: dw_hdmi: fix connector access for scdc
Commit 5d844091f237 ("drm/scdc-helper: Pimp SCDC debugs") changed the scdc
interface to pick up an i2c adapter from a connector instead. However, in
the case of dw-hdmi, the wrong connector was being used to pass i2c adapter
information, since dw-hdmi's embedded connector structure is only populated
when the bridge attachment callback explicitly asks for it.
drm-meson is handling connector creation, so this won't happen, leading to
a NULL pointer dereference.
Fix it by having scdc functions access dw-hdmi's current connector pointer
instead, which is assigned during the bridge enablement stage.
[narmstrong: moved Fixes tag before first S-o-b and added Reported-by tag] |
