| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: don't check the listener's sk_err in vsock_accept()
Syzbot reported an issue which can be reproduced with these steps:
r0 = socket(AF_VSOCK, SOCK_STREAM, 0)
bind(r0, {VMADDR_CID_ANY, PORT})
connect(r0, {VMADDR_CID_LOCAL, PORT}) -> -1, EPROTO (self-connect)
listen(r0, backlog) -> 0
r1 = socket(AF_VSOCK, SOCK_STREAM, 0)
connect(r1, {VMADDR_CID_LOCAL, PORT}) -> 0
accept(r0) -> -1, EPROTO (stale sk_err)
Basically, it creates a socket (r0) and triggers a self-connect after
binding it. This self-connect fails with EPROTO because it loops back
to r0 while the socket is still in the TCP_SYN_SENT state, causing it
to be incorrectly dispatched to the connecting-client path. The
unexpected packet type encountered there sets sk_err to EPROTO.
After that, it invokes a listen() call on the same socket. This
listen() call succeeds because the kernel's listening path never
inspects or clears sk_err. Then, a new socket (r1) is created as a
normal client and connects to r0. However, vsock_accept() rejects this
incoming connection because the listener's sk_err still holds the
EPROTO error from the earlier failed self-connect.
This rejection causes the child socket created for r1's connection to
never be freed on virtio or hyperv transports; only the VMCI transport
implements pending_work to revisit and clean up a rejected socket.
For a non-blocking connect(), vsock_connect() may return -EINPROGRESS
immediately, and vsock_connect_timeout() can later set sk->sk_err
asynchronously.
Since no vsock transport ever sets sk_err on a socket while it is in
TCP_LISTEN state, checking it in vsock_accept() serves no purpose and
only carries forward errors left behind by earlier, unrelated
connection attempts on the same socket. Remove the checks so accept()
no longer rejects valid incoming connections because of a stale
error, which also avoids the resource leak described above. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: skip double clone set expressions on element insert
Both the dynset and newsetelem path clone the existing set expressions
when setting set element expressions if no override expressions are
provided. This results in a double clone, once to clone the template set
expressions then another clone on the new element. Add a flag to
annotate if userspace provides a override expression (ie. expression of
the same type of the set but different configuration), otherwise borrow
the existing expression from the set. Add conditionals to release
expression iif they represent an override. Use this new override_exprs
flag to dump the dynset expression override to userspace.
This simplifies the existing logic and it also fixes a bug with the
connlimit expression which results in a module refcount imbalance
WARNING splat when resorting on the default set expressions. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-direct: return struct page from dma_direct_alloc_from_pool()
Commit 5b138c534fda ("dma-direct: factor out a dma_direct_alloc_from_pool
helper") changed dma_direct_alloc_from_pool() to return the CPU address
from dma_alloc_from_pool(). That fits dma_direct_alloc(), but
dma_direct_alloc_pages() also uses the helper and expects a struct page *.
Fix this by making dma_direct_alloc_from_pool() return the struct page *
again, and pass the CPU address back through an out-parameter for the
dma_direct_alloc() caller. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: transfer the pmd dirty bit to the folio on zap
zap_huge_pmd_folio() propagates the pmd young bit to the folio for the
file case, but not the dirty bit. The pte path does propagate it, in
zap_present_folio_ptes() and so does the pmd split path, in
__split_huge_pmd_locked().
For most file mappings the omission is harmless, because writing to a
shared file mapping goes through page_mkwrite(), which dirties the folio.
tmpfs is different: it has no page_mkwrite(), and vma_wants_writenotify()
is false for it, so a *read* fault on a MAP_SHARED tmpfs mapping installs
a writable pmd via do_read_fault(). do_read_fault() does not call
fault_dirty_shared_page(), so subsequent stores through that mapping set
only the hardware dirty bit in the pmd and never call folio_mark_dirty().
A shmem folio allocated by a fault is marked uptodate but not dirty (see
the clear: block in shmem_get_folio_gfp()), so PG_dirty is never set at
all.
Unmapping such a folio - munmap(), or exit_mmap() when the process dies -
then loses the only record that it was written, because zap_huge_pmd()
drops the pmd without transferring the dirty bit. Reclaim afterwards sees
a clean shmem folio: the whole swap-out block in shrink_folio_list() is
inside "if (folio_test_dirty(folio))", so pageout() is skipped and the
folio falls into __remove_mapping(). There, folio_is_file_lru() is false
for a swapbacked folio, so no shadow entry is created and
__filemap_remove_folio(folio, NULL) simply empties the i_pages slot. The
data is freed without ever being written to swap, and the next fault on
that index returns a freshly zeroed folio.
This is silent data loss for any process that keeps state in a MAP_SHARED
tmpfs segment across an unmap - for example a cache handed from one
process generation to the next through /dev/shm. It requires the folio to
be PMD-mapped, so it only shows up once shmem THP is enabled (which is
what we did in Meta fleet and started noticing crashes); with THP off the
pte path transfers the dirty bit correctly. It also only becomes visible
when swap is enabled, because with no swap device shmem folios (which are
on the anon LRU) are not scanned by reclaim at all, so the clean folio is
never dropped.
Reproduced on x86_64 with a tmpfs mounted huge=within_size: read-fault a
2MB-backed region, write a known pattern through the resulting mapping,
munmap, force reclaim of the cgroup, then re-map and read back. Without
this patch the region reads back as zeros and vmstat shows zswpout 0 - the
data was discarded rather than swapped. With this patch the region reads
back correctly and the pages are swapped out as expected. With
huge=never, or when the first touch is a write, the test passes either
way. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: harmony: initialize locks before requesting IRQ
snd_harmony_create() registers the IRQ before initializing h->lock and
h->mixer_lock. A pending interrupt can invoke the handler while these
locks are uninitialized.
Initialize both locks before requesting the IRQ so the handler always
sees valid lock state. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vfio-ap: Fix missing lock required to access list of ap_matrix_mdev objects
In order to traverse or add/remove ap_matrix_mdev objects in the
matrix_dev->mdev_list, the matrix_dev->guests_lock mutex must be held.
There are two functions that access the list without holding the mutex:
vfio_ap_mdev_probe function
~~~~~~~~~~~~~~~~~~~~~~~~~~~
The vfio_ap_mdev_probe function uses the matrix_dev->mdevs_lock
mutex to guard the add of a newly created ap_matrix_mdev object to the
matrix_dev->mdev_list. This mutex does not protect list access; its purpose
is to guard against concurrent access to fields contained in an
ap_matrix_mdev object. This could lead to kernel memory corruption or
use-after-free if another mdev is created or removed concurrently.
The adding of an ap_matrix_mdev object to matrix_dev->mdev_list
is now guarded by the matrix_dev->guests_lock which is the correct
way to protect against concurrent mdev_list access.
Also removed the following two lines of code because the matrix_mdev is
allocated via vfio_alloc_device macro which uses kzalloc, so req_trigger
and cfg_chg_trigger are already zero-initialised when the struct is
allocated before the call to vfio_register_emulated_iommu_dev. This
prevents a window whereby these triggers are set to NULL after
the device is exposed to userspace.
matrix_mdev->req_trigger = NULL;
matrix_mdev->cfg_chg_trigger = NULL;
vfio_ap_mdev_for_queue function
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The status_show function that supports display of the status attribute of
the devices in /sys/bus/ap/devices calls the vfio_ap_mdev_for_queue
function which iterates the matrix_dev->mdev_list to find the object
representing the queue device whose status is to be displayed. In order to
traverse this list, the matrix_dev->guests_lock mutex must be held.
To fix this, the guests_lock mutex is taken prior to taking the
matrix_dev->mdevs_lock mutex in the status_show function. It is taken
there rather than the vfio_ap_mdev_for_queue function - where it is
needed - because it must be taken prior to the mdevs_lock mutex in order to
adhere to the proper locking order and prevent a lockdep splat; also
because the mdevs_lock is needed there to access fields within
the matrix_mdev object in that function.
See the vfio-ap-locking.rst in the linux kernel tree. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Initialize NVMe abort_work once at submission
qla_nvme_fcp_abort() and qla_nvme_ls_abort() ran INIT_WORK() on
priv->abort_work immediately before schedule_work(). INIT_WORK()
reinitializes the work_struct, resetting its list head and clearing the
pending bit. If an abort is issued more than once for the same command
(for example, concurrent transport teardown and a timeout-driven abort),
the second INIT_WORK() reinitializes a work item that is already queued,
which can corrupt the workqueue list and lead to crashes or a looping
worker.
Initialize priv->abort_work once at command submission, next to the
existing per-command spin_lock_init(&priv->cmd_lock), and leave only
schedule_work() in the abort paths. schedule_work() already does nothing
when the work item is still pending, so a repeated abort no longer
disturbs an in-flight work item. The command is not returned to the
transport until the final kref_put()/release callback runs after
abort_work has completed, so the work item is idle before priv is reused
and the single submission-time INIT_WORK() is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to clear dirty flag on folio in error path
If node block is corrupted due to chksum mismatch or inconsistent
footer info, it needs to drop clear flag of node folio, in order
to persist inconsistent node data to storage. |
| In the Linux kernel, the following vulnerability has been resolved:
net: tap: fix wrong transport_header when sending VLAN-tagged frame
In tap_get_user_xdp(), when processing a VLAN-tagged frame (e.g.
ETH_P_8021Q), skb_set_network_header() is called first to advance
network_header past the VLAN tag to the inner protocol header.
skb_probe_transport_header() is then called with skb->protocol still
set to ETH_P_8021Q, while nhoff (derived from skb_network_offset())
already points past the VLAN tag to the inner protocol header.
In __skb_flow_dissect(), proto is initialized to ETH_P_8021Q and nhoff
points past the VLAN tag. When the dissector hits case ETH_P_8021Q, it
reads a struct vlan_hdr at the current nhoff via __skb_header_pointer(),
but that offset contains the inner protocol header (e.g. an IP header).
The bytes are misinterpreted as a VLAN header, yielding a garbage
encapsulated EtherType that matches no known protocol. The dissector
returns false, so skb_probe_transport_header() never calls
skb_set_transport_header(), leaving transport_header at its uninitialized
sentinel value (~0U).
Move skb_set_network_header() to after skb_probe_transport_header(). At
the time skb_probe_transport_header() is called, network_header still
points to the VLAN header (offset ETH_HLEN), so nhoff is correct and the
flow dissector can parse the VLAN header, extract the inner EtherType,
and advance nhoff to the inner protocol header, allowing transport_header
to be set correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/tegra: gr2d/gr3d: Initialize address register map before HOST1X client is registered
The host1x_client_register() function is called just prior to register map
initialization loop, making the device available to userspace. This may
result in userspace attempting to submits a job before the register map is
initialized. Address this by moving register initialization before host1x
client registration. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: bail out of setup if the controller is inaccessible
xhci_gen_setup() locates the operational registers using the capability
length read from the very first register:
xhci->op_regs = hcd->regs +
HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
If the controller is dead or has dropped off the bus, that read returns
~0, HC_LENGTH() truncates it to 0xff, and op_regs ends up 0xff bytes
past the page-aligned MMIO base, i.e. unaligned. The first access
through it, xhci_halt() -> xhci_handshake() reading op_regs->status, is
then an unaligned readl() on device memory. arm64 faults on unaligned
device accesses, so instead of xhci_handshake() catching the all-ones
value and returning -ENODEV, setup oopses:
xhci-pci-renesas 0005:08:00.0: Unable to change power state from D3cold to D0, device inaccessible
xhci-pci-renesas 0005:08:00.0: xHCI Host Controller
xhci-pci-renesas 0005:08:00.0: new USB bus registered, assigned bus number 1
Unable to handle kernel paging request at virtual address ffff80030a770103
ESR = 0x0000000096000021
FSC = 0x21: alignment fault
Internal error: Oops: 0000000096000021 [#1] SMP
pc : xhci_halt [xhci_hcd]
Call trace:
xhci_halt
xhci_gen_setup
xhci_pci_setup
usb_add_hcd
usb_hcd_pci_probe
xhci_pci_common_probe
xhci_pci_renesas_probe
This was hit with a Renesas uPD720201 that failed to power up ("Unable
to change power state from D3cold to D0, device inaccessible") yet still
reached the HCD probe path.
Read the capability register once, and if it reads back the all-ones
value (as xhci_handshake() and xhci_reset() already test for), abort
setup with -ENODEV before op_regs is derived from it. Reading it once
also avoids re-reading a register that may change under a concurrent
hot-removal. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix invalidate lock leak on open O_TRUNC DAX failure
fuse_open() takes filemap_invalidate_lock() for a DAX truncate
(dax_truncate = true) and releases it before the out_inode_unlock
label. But when fuse_dax_break_layouts() fails, the goto
out_inode_unlock skips the unlock and leaks the rwsem, so any later
fault or truncate on the file stalls on the stale lock.
fuse_dax_break_layouts() can fail with -ERESTARTSYS when a signal
interrupts the wait for busy DAX pages to drain:
open("file", O_RDWR | O_TRUNC)
└─ fuse_open()
├─ filemap_invalidate_lock() # dax_truncate
└─ fuse_dax_break_layouts()
└─ dax_break_layout()
└─ wait_page_idle() # TASK_INTERRUPTIBLE
└─ fuse_wait_dax_page() # unlock, schedule, re-lock
└─ signal → -ERESTARTSYS
goto out_inode_unlock # <- lock leaked
Fix this by moving filemap_invalidate_unlock() below the label so
that all error paths release the lock, and rename the label to
out_unlock as it now covers more than just the inode lock. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: Wrap user-invoked calls to fb_set_var() in helper
Handle fbcon during display updates in fb_set_var_from_user(). Check
with fbcon if the mode change is possible, update hardware state and
finally update fbcon. Update all callers.
Only the FBIOPUT_VSCREENINFO ioctl currently does all steps. Other
mode-changes callers in sysfs and driver code are missing fbcon-related
steps.
With the new helper, ps3fb and sh_mobile_lcdcfb no longer maintain
fbcon state themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: Avoid calling WARN_ON() on -ENOMEM in cfg802154_switch_netns()
It's pointless to call WARN_ON() in case of an allocation failure in
dev_change_net_namespace() and device_rename(), since it only leads to
useless splats caused by deliberate fault injections, so avoid it.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject sleepable BPF_LSM_CGROUP programs at load time
The cgroup shim runs under rcu_read_lock_dont_migrate(), so we should
not attach any sleepable BPF programs there. Add support to the verifier
to explicitly reject attempts to load sleepable BPF programs destined
for LSM cgroup attachment.
Without this, we get the following splat from a BPF_LSM_CGROUP
program marked BPF_F_SLEEPABLE attached to file_open when it calls
bpf_get_dentry_xattr():
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1567
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 34317, name: load
preempt_count: 0, expected: 0
RCU nest depth: 2, expected: 0
Call Trace:
down_read+0x76/0x480
ext4_xattr_get+0x11f/0x700
__vfs_getxattr+0xf0/0x150
bpf_get_dentry_xattr+0xbb/0xf0
bpf_prog_e76a298dac9218c6_test_open+0x6a/0x85
__cgroup_bpf_run_lsm_current+0x326/0x840
bpf_trampoline_6442534646+0x62/0x14d
security_file_open+0x34/0x60
do_dentry_open+0x340/0x1260
vfs_open+0x7a/0x440
path_openat+0x1bac/0x30a0
libbpf provides a .s named section variant for every sleepable
program type except lsm_cgroup, reflecting that per-cgroup LSM programs
are intended to only run in a non-sleepable context.
The above splat was obtained by bypassing libbpf by using bpf(2)
directly. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: sata_dwc_460ex: fix infinite loop in NCQ tag completion bit-scanning
The hand-rolled bit-scanning loop in the NCQ completion path has an
infinite loop bug. When tag_mask has only high bits set (e.g.
0x80000000), the inner while loop left-shifts tag_mask until it
overflows to 0. At that point !(0 & 1) is always true and 0 <<= 1
stays 0, causing an infinite loop in hardirq context with a spinlock
held.
Replace the open-coded bit-scanning with __ffs() which correctly
finds the least significant set bit and is bounded by the width of
the argument. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: use wiphy work for socket owner autodisconnect
nl80211_netlink_notify() walks the cfg80211 wireless device list when a
NETLINK_GENERIC socket is released. If the socket owns a connection, the
notifier queues the embedded wdev->disconnect_wk work item.
That work is a plain work_struct today. NETDEV_GOING_DOWN cancels it, but a
NETLINK_URELEASE notifier that already observed conn_owner_nlportid can
queue it after that cancel returns. _cfg80211_unregister_wdev() then
removes the wdev from the list and waits for RCU readers, but
synchronize_net() does not drain work queued by such a reader.
Make the autodisconnect work a wiphy_work instead. The callback already
needs the wiphy mutex, and wiphy_work runs under that mutex. This lets
teardown cancel pending autodisconnect work while holding the mutex,
without a cancel_work_sync() vs. worker locking concern.
Also cancel the wiphy work after list_del_rcu() and synchronize_net(). Any
NETLINK_URELEASE notifier that had already reached the wdev list has then
either queued the work and it is removed, or can no longer find the wdev. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Move jump_label_init() before parse_early_param()
When enabling both CONFIG_MEM_ALLOC_PROFILING=y and
CONFIG_MEM_ALLOC_PROFILING_ENABLED_BY_DEFAULT=y, then diabling memory
profiling by adding the boot parameter 'sysctl.vm.mem_profiling=0' will
cause the kernel failed to boot.
After analysis, this is because jump_label_init() must be called before
parse_early_param(), the early param handlers may modify static keys by
static_branch_enable/disable().
Fix this by moving jump_label_init() to before parse_early_param(). The
solution is similar to other architectures. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Detach event groups during remove_on_exec
perf_event_remove_on_exec() removes events by calling
perf_event_exit_event(). For top-level events, this removes the event from
the context with DETACH_EXIT only.
This can leave inconsistent group state when a removed event is a group
leader and the group contains siblings without remove_on_exec. If the group
was active, the surviving siblings can remain active and attached to the
removed leader's sibling list, but are no longer represented by a valid
group leader on the PMU context active lists.
A later close of the removed leader uses DETACH_GROUP and can promote the
still-active siblings from this stale group state. The next schedule-in can
then add an already-linked active_list entry again, corrupting the PMU
context active list.
With DEBUG_LIST enabled, this is caught as a list_add double-add in
merge_sched_in().
Fix this by detaching group relationships when remove_on_exec removes an
event. This preserves the existing task-exit and revoke behavior, while
ensuring surviving siblings are ungrouped before the removed event leaves
the context. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix deadlock between reflink and transaction commit when using flushoncommit
When using the flushoncommit mount option, we can have a deadlock between
a transaction commit and a reflink operation that copied an inline extent
to an offset beyond the current i_size of the destination node.
The deadlock happens like this:
1) Task A clones an inline extent from inode X to an offset of inode Y
that is beyond Y's current i_size. This means we copied the inline
extent's data to a folio of inode Y that is beyond its EOF, using a
call to copy_inline_to_page();
2) Task B starts a transaction commit and calls
btrfs_start_delalloc_flush() to flush delalloc;
3) The delalloc flushing sees the new dirty folio of inode Y and when it
attempts to flush it, it ends up at extent_writepage() and sees that
the offset of the folio is beyond the i_size of inode Y, so it attempts
to invalidate the folio by calling folio_invalidate(), which ends up at
btrfs' folio invalidate callback - btrfs_invalidate_folio(). There it
tries to lock the folio's range in inode Y's extent io tree, but it
blocks since it's currently locked by task A - during a reflink we lock
the inodes and the source and destination ranges after flushing all
delalloc and waiting for ordered extent completion - after that we
don't expect to have dirty folios in the ranges, the exception is if
we have to copy an inline extent's data (because the destination offset
is not zero);
4) Task A then attempts to start a transaction to update the inode item,
and then it's blocked since the current transaction is in the
TRANS_STATE_COMMIT_START state. Therefore task A has to wait for the
current transaction to become unblocked (its state >=
TRANS_STATE_UNBLOCKED).
So task A is waiting for the transaction commit done by task B, and
the later waiting on the extent lock of inode Y that is currently
held by task A.
Syzbot recently reported this with the following stack traces:
INFO: task kworker/u8:7:1053 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:7 state:D stack:23520 pid:1053 tgid:1053 ppid:2 task_flags:0x4208060 flags:0x00080000
Workqueue: writeback wb_workfn (flush-btrfs-46)
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5298 [inline]
__schedule+0x1553/0x5240 kernel/sched/core.c:6911
__schedule_loop kernel/sched/core.c:6993 [inline]
schedule+0x164/0x360 kernel/sched/core.c:7008
wait_extent_bit fs/btrfs/extent-io-tree.c:811 [inline]
btrfs_lock_extent_bits+0x59c/0x700 fs/btrfs/extent-io-tree.c:1914
btrfs_lock_extent fs/btrfs/extent-io-tree.h:152 [inline]
btrfs_invalidate_folio+0x43d/0xc40 fs/btrfs/inode.c:7704
extent_writepage fs/btrfs/extent_io.c:1852 [inline]
extent_write_cache_pages fs/btrfs/extent_io.c:2580 [inline]
btrfs_writepages+0x12ff/0x2440 fs/btrfs/extent_io.c:2713
do_writepages+0x32e/0x550 mm/page-writeback.c:2554
__writeback_single_inode+0x133/0x11a0 fs/fs-writeback.c:1750
writeback_sb_inodes+0x995/0x19d0 fs/fs-writeback.c:2042
wb_writeback+0x456/0xb70 fs/fs-writeback.c:2227
wb_do_writeback fs/fs-writeback.c:2374 [inline]
wb_workfn+0x41a/0xf60 fs/fs-writeback.c:2414
process_one_work kernel/workqueue.c:3276 [inline]
process_scheduled_works+0xb6e/0x18c0 kernel/workqueue.c:3359
worker_thread+0xa53/0xfc0 kernel/workqueue.c:3440
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x51e/0xb90 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
INFO: task syz.4.64:6910 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.4.64 state:D stack:22752 pid:6910 tgid:
---truncated--- |
